VMV3 datasheet(140/212 Pages) MICROSEMI

140 / 212 page

Military ProASIC3/EL DC and Switching Characteristics

2-126

Revision 3

Table 2-201 • Military ProASIC3/EL CCC/PLL Specification

For Devices Operating at 1.5 V DC Core Voltage

Parameter

Min.

Typ.

Max.

Units

Clock Conditioning Circuitry Input Frequency fIN_CCC

1.5

350

MHz

Clock Conditioning Circuitry Output Frequency fOUT_CCC

0.75

350

MHz

Delay Increments in Programmable Delay Blocks 1, 2

160

Number of Programmable Values in Each Programmable Delay Block

Serial Clock (SCLK) for Dynamic PLL3

110

MHz

Input cycle-to-cycle jitter (peak magnitude)

1.5

Acquisition Time

LockControl = 0

300

µs

LockControl = 1

6.0

Tracking Jitter4

LockControl = 0

1.6

LockControl = 1

0.8

Output Duty Cycle

48.5

51.5

Delay Range in Block: Programmable Delay 1 1,2

0.6

5.56

Delay Range in Block: Programmable Delay 2 1,2

0.025

5.56

Delay Range in Block: Fixed Delay 1,2

2.2

CCC Output Peak-to-Peak Period Jitter FCCC_OUT

Max. Peak-to-Peak Period Jitter 5,6

SSO

 2 SSO  4 SSO  8 SSO  16

0.75 MHz to 50 MHz

0.50%

0.70%

1.00%

50 MHz to 250 MHz

1.00%

3.00%

5.00%

9.00%

250 MHz to 350 MHz

2.50%

4.00%

6.00%

12.00%

Notes:

1. This delay is a function of voltage and temperature. See Table 2-5 on page 2-8 for deratings.

2. TJ = 25°C, VCC = 1.5 V.

3. Maximum value obtained for a -1 speed grade device in worst-case military conditions. For specific junction temperature

and voltage supply levels, refer to Table 2-5 on page 2-8 for derating values.

4. Tracking jitter is defined as the variation in clock edge position of PLL outputs with reference to PLL input clock edge.

Tracking jitter does not measure the variation in PLL output period, which is covered by period jitter parameter.

5. Measurements done with LVTTL 3.3 V, 8 mA I/O drive strength and high slew rate. VCC/VCCPLL = 1.425 V,

VQ/PQ/TQ type of packages, 20 pF load.

6. Switching I/Os are placed outside of the PLL bank.

Note:

Peak-to-peak jitter measurements are defined by Tpeak-to-peak = Tperiod_max – Tperiod_min.

Figure 2-43 • Peak-to-Peak Jitter Definition

Tperiod_max

Tperiod_min

Output Signal

VMV3 датащи(PDF) 140 Page - Microsemi Corporation

VMV3 датащи(HTML) 140 Page - Microsemi Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL