WM8985GEFLSLASHR datasheet(57/121 Pages) WOLFSON

57 / 121 page

Production Data

WM8985

PD, Rev 4.6, July 2009

The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital

interpolation filters. The bitstream data enters the multi-bit, sigma-delta DACs, which convert it to a

high quality analogue audio signal. The multi-bit DAC architecture reduces high frequency noise and

sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and

low distortion.

The DAC output phase defaults to non-inverted. Setting DACLPOL will invert the DAC output phase

on the left channel and DACRPOL inverts the phase on the right channel.

AUTO-MUTE

The DAC has an auto-mute function which applies an analogue mute when 1024 consecutive zeros

are detected. The mute is released as soon as a non-zero sample is detected. Auto-mute can be

disabled using the AMUTE control bit.

DIGITAL HI-FI DAC VOLUME (GAIN) CONTROL

The signal volume from each Hi-Fi DAC can be controlled digitally. The gain range is –127dB to 0dB

in 0.5dB steps. The level of attenuation for an eight-bit code X is given by:

0.5

× (X-255) dB for 1 ≤ X ≤ 255;

MUTE for X = 0

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R11 (0Bh)

Left DAC

Digital Volume

7:0

DACLVOL

[7:0]

11111111

( 0dB )

Left DAC Digital Volume Control

0000 0000 = Digital Mute

0000 0001 = -127dB

0000 0010 = -126.5dB

... 0.5dB steps up to

1111 1111 = 0dB

DACVU

Not

latched

DAC left and DAC right volume do

not update until a 1 is written to

DACVU (in reg 11 or 12)

R12 (0Ch)

Right DAC

Digital Volume

7:0

DACRVOL

[7:0]

11111111

( 0dB )

Right DAC Digital Volume Control

0000 0000 = Digital Mute

0000 0001 = -127dB

0000 0010 = -126.5dB

... 0.5dB steps up to

1111 1111 = 0dB

DACVU

Not

latched

DAC left and DAC right volume do

not update until a 1 is written to

DACVU (in reg 11 or 12)

Table 23 DAC Digital Volume Control

Note:

An additional gain of up to 12dB can be added using the gain block embedded in the

digital peak limiter circuit (see DAC OUTPUT LIMITER section).

5-BAND EQUALISER

A 5-band graphic equaliser function which can be used to change the output frequency levels to suit

the environment. This can be applied to the ADC or DAC path and is described in the 5-BAND

EQUALISER section for further details on this feature.

3-D ENHANCEMENT

The WM8985 has an advanced digital 3-D enhancement feature which can be used to vary the

perceived stereo separation of the left and right channels. Like the 5-band equaliser this feature can

be applied to either the ADC record path or the DAC playback path but not both simultaneously.

Refer to the 3-D STEREO ENHANCEMENT section for further details on this feature.

DAC DIGITAL OUTPUT LIMITER

The WM8985 has a digital output limiter function. The operation of this is shown in Figure 24. In

this diagram the upper graph shows the envelope of the input/output signals and the lower graph

shows the gain characteristic.

WM8985GEFL/R датащи(PDF) 57 Page - Wolfson Microelectronics plc

WM8985GEFL/R датащи(HTML) 57 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL