C167CS-L datasheet(55/81 Pages) INFINEON

55 / 81 page

C167CS-4R

C167CS-L

Data Sheet

V2.2, 2001-08

Input leakage current (all other)

IOZ2 CC –

±500

0.45 V <

VIN

VDD

RSTIN inactive current6)

IRSTH

–

-10

µA

VIN = VIH1

RSTIN active current6)

IRSTL

-100

–

µA

VIN = VIL

READY/RD/WR inact. current9)

IRWH

–

-40

µA

VOUT = 2.4 V

READY/RD/WR active current9)

IRWL

-500

–

µA

VOUT = VOLmax

ALE inactive current9)

IALEL

–

µA

VOUT = VOLmax

ALE active current9)

IALEH

500

–

µA

VOUT = 2.4 V

Port 6 inactive current9)

IP6H

–

-40

µA

VOUT = 2.4 V

Port 6 active current9)

IP6L

-500

–

µA

VOUT = VOL1max

PORT0 configuration current10)

IP0H

–

-10

µA

VIN = VIHmin

IP0L

-100

–

µA

VIN = VILmax

XTAL1 input current

IIL

CC –

±20

µA0 V < VIN < VDD

Pin capacitance11)

(digital inputs/outputs)

CIO CC –

f = 1 MHz

TA = 25 °C

1) Keeping signal levels within the levels specified in this table, ensures operation without overload conditions.

For signal levels outside these specifications also refer to the specification of the overload current

IOV.

2) For pin RSTIN this specification is only valid in bidirectional reset mode.

3) The maximum deliverable output current of a port driver depends on the selected output driver mode, see

Table 10, Current Limits for Port Output Drivers. The limit for pin groups must be respected.

4) As a rule, with decreasing output current the output levels approach the respective supply level (V

OL → VSS,

VOH → VDD). However, only the levels for nominal output currents are guaranteed.

5) This specification is not valid for outputs which are switched to open drain mode. In this case the respective

output will float and the voltage results from the external circuitry.

6) These parameters describe the RSTIN pullup, which equals a resistance of ca. 50 to 250 kΩ.

7) The maximum current may be drawn while the respective signal line remains inactive.

8) The minimum current must be drawn in order to drive the respective signal line active.

9) This specification is valid during Reset and during Hold-mode or Adapt-mode. During Hold-mode Port 6 pins

are only affected, if they are used (configured) for CS output and the open drain function is not enabled. The

READY-pullup is always active, except for Powerdown mode.

10) This specification is valid during Reset and during Adapt-mode.

11) Not 100% tested, guaranteed by design and characterization.

DC Characteristics (cont’d)

(Operating Conditions apply)1)

Parameter

Symbol

Limit Values

Unit Test Condition

min.

max.

C167CS-L датащи(PDF) 55 Page - Infineon Technologies AG

C167CS-L датащи(HTML) 55 Page - Infineon Technologies AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

датащи скачать

ссылки URL