ADS5400IPZP datasheet(46/58 Pages) TI2

46 / 58 page

SINAD

10Log

SNR

10Log

ADS5400

SLAS611C – OCTOBER 2009 – REVISED JANUARY 2016

www.ti.com

11 Device and Documentation Support

11.1 Device Support

11.1.1 Device Nomenclature

Analog Bandwidth The analog input frequency at which the power of the fundamental is reduced by 3 dB with

respect to the low-frequency value

Aperture Delay The delay in time between the rising edge of the input sampling clock and the actual time at

which the sampling occurs

Aperture Uncertainty (Jitter) The sample-to-sample variation in aperture delay

Clock Pulse Duration/Duty Cycle The duty cycle of a clock signal is the ratio of the time the clock signal

remains at a logic high (clock pulse duration) to the period of the clock signal, expressed as a

percentage.

Differential Nonlinearity (DNL) An ideal ADC exhibits code transitions at analog input values spaced exactly 1

LSB apart. DNL is the deviation of any single step from this ideal value, measured in units of LSB.

Common-Mode Rejection Ratio (CMRR) CMRR measures the ability to reject signals that are presented to

both analog inputs simultaneously. The injected common-mode frequency level is translated into

dBFS, the spur in the output FFT is measured in dBFS, and the difference is the CMRR in dB.

Effective Number of Bits (ENOB) ENOB is a measure in units of bits of a converter's performance as

compared to the theoretical limit based on quantization noise

ENOB = (SINAD – 1.76)/ 6.02

(7)

Gain Error

Gain error is the deviation of the ADC actual input full-scale range from its ideal value, given as a

percentage of the ideal input full-scale range.

Integral Nonlinearity (INL) INL is the deviation of the ADC transfer function from a best-fit line determined by a

least-squares curve fit of that transfer function. The INL at each analog input value is the difference

between the actual transfer function and this best-fit line, measured in units of LSB.

Offset Error Offset error is the deviation of output code from mid-code when both inputs are tied to common-

mode.

Power-Supply Rejection Ratio (PSRR) PSRR is a measure of the ability to reject frequencies present on the

power supply. The injected frequency level is translated into dBFS, the spur in the output FFT is

measured in dBFS, and the difference is the PSRR in dB. The measurement calibrates out the

benefit of the board supply decoupling capacitors.

Signal-to-Noise Ratio (SNR) SNR is the ratio of the power of the fundamental (PS) to the noise floor power

(PN), excluding the power at DC and in the first five harmonics

(8)

SNR is either given in units of dBc (dB to carrier) when the absolute power of the

fundamental is used as the reference, or dBFS (dB to full scale) when the power of the

fundamental is extrapolated to the converter’s full-scale range.

Signal-to-Noise and Distortion (SINAD) SINAD is the ratio of the power of the fundamental (PS) to the power

of all the other spectral components including noise (PN) and distortion (PD), but excluding DC.

(9)

SINAD is either given in units of dBc (dB to carrier) when the absolute power of the

fundamental is used as the reference, or dBFS (dB to full scale) when the power of the

fundamental is extrapolated to the converter’s full-scale range.

Temperature Drift Temperature drift (with respect to gain error and offset error) specifies the change from the

value at the nominal temperature to the value at TMIN or TMAX. It is computed as the maximum

variation the parameters over the whole temperature range divided by TMIN – TMAX.

Submit Documentation Feedback

Product Folder Links: ADS5400

ADS5400IPZP датащи(PDF) 46 Page - Texas Instruments

ADS5400IPZP датащи(HTML) 46 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

датащи скачать

ссылки URL