UPSD3422 datasheet(59/293 Pages) STMICROELECTRONICS

59 / 293 page

uPSD34xx

MCU clock generation

59/293

MCU clock generation

Internal system clocks generated by the clock generation unit are derived from the signal,

XTAL1, shown in Figure 14. XTAL1 has a frequency fOSC, which comes directly from the

external crystal or oscillator device. The SFR named CCON0 (Table 22 on page 62) controls

the clock generation unit.

There are two clock signals produced by the clock generation unit:

●

MCU_CLK

●

PERIPH_CLK

14.1

MCU_CLK

This clock drives the 8032 MCU core and the Watchdog Timer (WDT). The frequency of

MCU_CLK is equal to fOSC by default, but it can be divided by as much as 2048, shown in

Figure 14. The bits CPUPS[2:0] select one of eight different divisors, ranging from 2 to 2048.

The new frequency is available immediately after the CPUPS[2:0] bits are written. The final

frequency of MCU_CLK is fMCU.

MCU_CLK is blocked by either bit, PD or IDL, in the SFR named PCON during MCU Power-

down Mode or Idle Mode respectively.

MCU_CLK clock can be further divided as required for use in the WDT. See details of the

WDT in Section 19: Supervisory functions on page 83.

14.2

PERIPH_CLK

This clock drives all the uPSD34xx peripherals except the WDT. The Frequency of

PERIPH_CLK is always fOSC. Each of the peripherals can independently divide

PERIPH_CLK to scale it appropriately for use.

PERIPH_CLK runs at all times except when blocked by the PD bit in the SFR named PCON

during MCU Power-down Mode.

14.2.1

JTAG Interface Clock

The JTAG interface for ISP and for Debugging uses the externally supplied JTAG clock,

coming in on pin TCK. This means the JTAG ISP interface is always available, and the JTAG

Debug interface is available when enabled, even during MCU Idle mode and Power-down

Mode.

However, since the MCU participates in the JTAG debug process, and MCU_CLK is halted

during Idle and Power-down Modes, the majority of debug functions are not available during

these low power modes. But the JTAG debug interface is capable of executing a reset

command while in these low power modes, which will exit back to normal operating mode

where all debug commands are available again.

The CCON0 SFR contains a bit, DBGCE, which enables the breakpoint comparators inside

the JTAG Debug Unit when set. DBGCE is set by default after reset, and firmware may clear

this bit at run-time. Disabling these comparators will reduce current consumption on the

MCU Module, and it is recommended to do so if the Debug Unit will not be used (such as in

the production version of an end-product).

UPSD3422 датащи(PDF) 59 Page - STMicroelectronics

UPSD3422 датащи(HTML) 59 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL