PIC16F627A datasheet(86/180 Pages) MICROCHIP

86 / 180 page

PIC16F627A/628A/648A

DS40044D-page 84

12.4

USART Synchronous Master

Mode

In Synchronous Master mode, the data is transmitted in

a half-duplex manner (i.e., transmission and reception

do not occur at the same time). When transmitting data,

the reception is inhibited and vice versa. Synchronous

mode is entered by setting bit SYNC (TXSTA<4>). In

addition enable bit SPEN (RCSTA<7>) is set in order to

configure the RB2/TX/CK and RB1/RX/DT I/O pins to

CK (clock) and DT (data) lines, respectively. The

Master mode indicates that the processor transmits the

master clock on the CK line. The Master mode is

entered by setting bit CSRC (TXSTA<7>).

12.4.1

USART SYNCHRONOUS MASTER

TRANSMISSION

The USART transmitter block diagram is shown in

Figure 12-1. The heart of the transmitter is the Transmit

(serial) Shift Register (TSR). The shift register obtains

its data from the read/write transmit buffer register,

TXREG. The TXREG register is loaded with data in

software. The TSR register is not loaded until the last

bit has been transmitted from the previous load. As

soon as the last bit is transmitted, the TSR is loaded

with new data from the TXREG (if available). Once the

TXREG register transfers the data to the TSR register

(occurs in one Tcycle), the TXREG is empty and

interrupt bit, TXIF (PIR1<4>) is set. The interrupt can

be enabled/disabled by setting/clearing enable bit TXIE

(PIE1<4>). Flag bit TXIF will be set regardless of the

state of enable bit TXIE and cannot be cleared in

software. It will reset only when new data is loaded into

the TXREG register. While flag bit TXIF indicates the

status of the TXREG register, another bit TRMT

(TXSTA<1>) shows the status of the TSR register.

TRMT is a read-only bit which is set when the TSR is

empty. No interrupt logic is tied to this bit, so the user

has to poll this bit in order to determine if the TSR

memory so it is not available to the user.

Transmission is enabled by setting enable bit TXEN

(TXSTA<5>). The actual transmission will not occur

until the TXREG register has been loaded with data.

The first data bit will be shifted out on the next available

rising edge of the clock on the CK line. Data out is

stable around the falling edge of the synchronous clock

(Figure 12-8). The transmission can also be started by

first loading the TXREG register and then setting bit

TXEN (Figure 12-9). This is advantageous when slow

baud rates are selected, since the BRG is kept in Reset

when bits TXEN, CREN and SREN are clear. Setting

enable bit TXEN will start the BRG, creating a shift

clock immediately. Normally, when transmission is first

started, the TSR register is empty, so a transfer to the

TXREG register will result in an immediate transfer to

TSR resulting in an empty TXREG. Back-to-back

transfers are possible.

Clearing enable bit TXEN during a transmission will

cause the transmission to be aborted and will reset the

transmitter. The DT and CK pins will revert to high-

impedance. If either bit CREN or bit SREN is set during

a transmission, the transmission is aborted and the DT

pin reverts to a high-impedance state (for a reception).

The CK pin will remain an output if bit CSRC is set

(internal clock). The transmitter logic however is not

reset although it is disconnected from the pins. In order

to reset the transmitter, the user has to clear bit TXEN.

If bit SREN is set (to interrupt an on-going transmission

and receive a single word), then after the single word is

received, bit SREN will be cleared and the serial port

will revert back to transmitting since bit TXEN is still set.

The DT line will immediately switch from high-imped-

ance Receive mode to transmit and start driving. To

avoid this, bit TXEN should be cleared.

In order to select 9-bit transmission, the TX9

(TXSTA<6>) bit should be set and the ninth bit should

be written to bit TX9D (TXSTA<0>). The ninth bit must

be written before writing the 8-bit data to the TXREG

result in an immediate transfer of the data to the TSR

the TXREG was written before writing the “new” TX9D,

the “present” value of bit TX9D is loaded.

Follow these steps when setting up a Synchronous

Master Transmission:

TRISB<1> and TRISB<2> should both be set to

‘1’ to configure the RB1/RX/DT and RB2/TX/CK

pins as inputs. Output drive, when required, is

controlled by the peripheral circuitry.

Initialize the SPBRG register for the appropriate

baud rate (Section 12.1 “USART Baud Rate

Generator (BRG)”).

Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

If interrupts are desired, then set enable bit

TXIE.

If 9-bit transmission is desired, then set bit TX9.

Enable the transmission by setting bit TXEN.

If 9-bit transmission is selected, the ninth bit

should be loaded in bit TX9D.

Start each transmission by loading data to the

TXREG register.

PIC16F627A датащи(PDF) 86 Page - Microchip Technology

PIC16F627A датащи(HTML) 86 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL