 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
INA700 датащи(PDF) 23 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
INA700 датащи(HTML) 23 Page - Texas Instruments |
|
|
23 / 50 page  The main device then generates a repeated start condition (a repeated start condition has the same timing as the start condition). After this repeated start condition, the protocol is the same as F/S mode, except that transmission speeds up to 2.94 MHz are allowed. Instead of using a stop condition, use repeated start conditions to maintain the bus in HS-mode. A stop condition ends the HS-mode and switches all the internal filters of the device to support the F/S mode. 7.5.1.3 SMBus Alert Response The INA700 is designed to respond to the SMBus Alert Response address. The SMBus Alert Response provides a quick fault identification for simple secondary devices. When an Alert occurs, the main device can broadcast the Alert Response secondary device address (0001 100) with the R/W bit set high. Following this Alert Response, any secondary device that generates an alert can identify itself by acknowledging the Alert Response and sending its address to the bus. The Alert Response can activate several different target devices simultaneously, similar to the I2C General Call. If more than one target attempts to respond, bus arbitration rules apply. The losing device does not generate an Acknowledge and continues to hold the Alert line low until that device wins arbitration. 7.6 Register Maps 7.6.1 INA700 Registers Table 7-3 lists the INA700 registers. All register locations not listed in Table 7-3 are considered reserved locations and the register contents should not be modified. Table 7-3. INA700 Registers Address Acronym Register Name Register Size (bits) Section 0h CONFIG Configuration 16 Go 1h ADC_CONFIG ADC Configuration 16 Go 5h VBUS Bus Voltage Measurement 16 Go 6h DIETEMP Temperature Measurement 16 Go 7h CURRENT Current Result 16 Go 8h POWER Power Result 24 Go 9h ENERGY Energy Result 40 Go Ah CHARGE Charge Result 40 Go Bh ALERT_DIAG Diagnostic Flags and Alert 16 Go Ch COL Current Over-Limit Threshold 16 Go Dh CUL Current Under-Limit Threshold 16 Go Eh BOVL Bus Overvoltage Threshold 16 Go Fh BUVL Bus Undervoltage Threshold 16 Go 10h TEMP_LIMIT Temperature Over-Limit Threshold 16 Go 11h PWR_LIMIT Power Over-Limit Threshold 16 Go 3Eh MANUFACTURER_ID Manufacturer ID 16 Go Complex bit access types are encoded to fit into small table cells. Table 7-4 shows the codes that are used for access types in this section. Table 7-4. INA700 Access Type Codes Access Type Code Description Read Type R R Value can be read only Write Type W W Value can be written only Read or Write Type www.ti.com INA700 SBOSAB4A – MAY 2023 – REVISED SEPTEMBER 2023 Copyright © 2023 Texas Instruments Incorporated Submit Document Feedback 23 Product Folder Links: INA700 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
