DRV8461SPWPR datasheet(67/117 Pages) TI

67 / 117 page

7.3.20.5 Functional Modes Summary

Table 7-30. Functional Modes Summary

CONDITION

CONFIGURATION

H-BRIDGE

DVDD

Regulator

CHARGE

PUMP

INDEXER

Logic

Sleep mode

4.5 V < VM <

65 V

nSLEEP pin = 0

Disabled

Disbaled

Disabled

Operating

4.5 V < VM <

65 V

nSLEEP pin = 1

ENABLE = 1 and EN_OUT =

Operating

Disabled

4.5 V < VM <

65 V

nSLEEP pin = 1

ENABLE pin = 0 or EN_OUT

= 0b

Disabled

Operating

7.4 Programming

7.4.1 Serial Peripheral Interface (SPI) Communication

When configured to operate with SPI interface, the device has full duplex, 4-wire synchronous communication

that is used to set device configurations, operating parameters, and read out diagnostic information from the

device. This section describes the SPI protocol, the command structure, and the control and status registers.

The SPI operates in target mode and can be connected with a controller in the following configurations:

• One target device

• Multiple target devices in parallel connection

• Multiple target devices in series (daisy chain) connection

7.4.1.1 SPI Format

The serial data input (SDI) word consists of a 16-bit word, with an 8 bit-command (A1), followed by 8-bit data

(D1). The serial data output (SDO) word consists of 8 bits of status register with fault status indication (S1),

followed by a report byte (R1). Figure 7-48 shows the data sequence between the controller and the SPI target

driver.

nSCS

SDI

SDO

Figure 7-48. SPI Format - Standard "16-bit" Frame

A valid frame must meet the following conditions:

• The SCLK pin must be low when the nSCS pin goes low and when the nSCS pin goes high.

• The nSCS pin should be taken high for at least 500 ns between frames.

• When the nSCS pin is asserted high, any signals at the SCLK and SDI pins are ignored, and the SDO pin is

in the high-impedance state (Hi-Z).

• A full 16 SCLK cycles must occur for a valid transaction for a standard frame, or alternately, for a daisy

chainframe with "n" number of peripheral devices, 16 + (n x 16) SCLK cycles must occur for a valid

transaction. Else, a frame error (SPI_ERROR) is reported and the data is ignored if it is a WRITE operation.

• Data on SDO from the device is propagated on the rising edge of SCLK, while data on SDI is captured by

thedevice on the subsequent falling edge of SCLK.

• The most-significant bit (MSB) is shifted in and out first.

www.ti.com

DRV8461

SLOSE98 – DECEMBER 2022

Submit Document Feedback

Product Folder Links: DRV8461

DRV8461SPWPR датащи(PDF) 67 Page - Texas Instruments

DRV8461SPWPR датащи(HTML) 67 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL