TSB41BA3APFP datasheet(42/66 Pages) TI

42 / 66 page

TSB41BA3A

IEEE 1394b THREEPORT CABLE TRANSCEIVER/ARBITER

SLLS618B − JUNE 2004 − REVISED AUGUST 2004

POST OFFICE BOX 655303

• DALLAS, TEXAS 75265

PRINCIPLES OF OPERATION (1394a-2000 INTERFACE)

status transfer (continued)

The sequence of events for a status transfer is as follows:

(a) Status transfer initiated. The PHY indicates a status transfer by asserting status on the CTL lines along with

the status data on the D0 and D1 lines (only 2 bits of status are transferred per cycle). Normally (unless

interrupted by a receive operation), a status transfer is either 2 or 8 cycles long. A 2-cycle (4-bit) transfer

occurs when only status information is to be sent. An 8-cycle (16-bit) transfer occurs when register data is

to be sent in addition to any status information.

(b) Status transfer terminated. The PHY normally terminates a status transfer by asserting idle on the CTL lines.

The PHY may also interrupt a status transfer at any cycle by asserting receive on the CTL lines to begin

a receive operation. The PHY asserts at least one idle cycle between consecutive status transfers.

receive

Whenever the PHY detects the data-prefix state on the serial bus, it initiates a receive operation by asserting

receive on the CTL terminals and a logic 1 on each of the D bus terminals (data-on indication). The PHY

indicates the start of a packet by placing the speed code (encoded as shown in Table 21) on the D terminals,

followed by packet data. The PHY holds the CTL terminals in the receive state until the last symbol of the packet

has been transferred. The PHY indicates the end of packet data by asserting idle on the CTL terminals. All

received packets are transferred to the LLC. Note that the speed code is part of the PHY-LLC protocol and is

not included in the calculation of CRC or any other data protection mechanisms.

It is possible for the PHY to receive a null packet, which consists of the data-prefix state on the serial bus followed

by the data-end state, without any packet data. A null packet is transmitted whenever the packet speed exceeds

the capability of the receiving PHY, or whenever the LLC immediately releases the bus without transmitting any

data. In this case, the PHY asserts receive on the CTL terminals with the data-on indication (all 1s) on the D

bus terminals, followed by Idle on the CTL terminals, without any speed code or data being transferred. In all

cases, in normal operation, the TSB41BA3A sends at least one data-on indication before sending the speed

code or terminating the receive operation.

The TSB41BA3A also transfers its own self-ID packet, transmitted during the self-ID phase of bus initialization,

to the LLC. This packet it transferred to the LLC just as any other received self-ID packet.

SPD

(a)

(b)

FF (data-on)

D0–D7

CTL0, CTL1

SYSCLK

(c)

(d)

(e)

NOTE A: SPD = Speed code, see Table 21. d0–dn = Packet data

Figure 15. Normal Packet Reception Timing

TSB41BA3APFP датащи(PDF) 42 Page - Texas Instruments

TSB41BA3APFP датащи(HTML) 42 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66

датащи скачать

ссылки URL