REV. 0

AD9886

–19–

2-Wire Serial Register Map

The AD9886 is initialized and controlled by a set of registers, which determine the operating modes. An external controller is

employed to write and read the Control Registers through the 2-line serial interface port.

Table V. Control Register Map

Write and

Hex

Read or

Default

Register

Address

Read Only

Bits

Value

Name

Function

RO

7:0

Chip Revision

Bits 7 through 4 represent functional revisions to the analog interface.

Bits 3 through 0 represent nonfunctional related revisions.

Revision 0 = 0000 0000

01H

R/

W

7:0

01101001

PLL Div MSB

This register is for Bits [11:4] of the PLL divider. Larger values mean

the PLL operates at a faster rate. This register should be loaded first

whenever a change is needed. (This will give the PLL more time to

lock.) See Note 1 .

02H

R/

W

7:4

1101

****

PLL Div LSB

Bits [7:4] LSBs of the PLL divider word. See Note 1.

03H

R/

W

7:2

1

*******

VCO/CPMP

Bit 7—Must be set to 1 for proper device operation.

*01*****

Bits [6:5] VCO Range. Selects VCO frequency range. (See PLL

description.)

***001**

Bits [4:2] Charge Pump Current. Varies the current that drives the

low-pass filter. (See PLL description.)

04H

R/

W

7:3

01000

***

Phase Adjust

ADC Clock phase adjustment. Larger values mean more delay.

(1 LSB = T/32.)

05H

R/

W

7:0

10000000

Clamp

Places the Clamp signal an integer number of clock periods after the trail-

Placement

ing edge of the Hsync signal.

06H

R/

W

7:0

10000000

Clamp

Number of clock periods that the Clamp signal is actively clamping.

Duration

07H

R/

W

7:0

00100000

Hsync Output

Sets the number of pixel clocks that HSOUT will remain active.

Pulsewidth

08H

R/

W

7:0

10000000

Red Gain

Controls ADC input range (Contrast) of each respective channel.

Bigger values give less contrast.

09H

R/

W

7:0

10000000

Green Gain

0AH

R/

W

7:0

10000000

Blue Gain

0BH

R/

W

7:1

1000000

*

Red Offset

Controls dc offset (Brightness) of each respective channel. Bigger

values decrease brightness.

0CH

R/

W

7:1

1000000

*

Green Offset

0DH

R/

W

7:1

1000000

*

Blue Offset

0EH

R/

W

7:3

1

*******

Mode

Bit 7—Channel Mode. Determines Single Channel or Dual Channel

Control 1

Output Mode. (Logic 0 = Single Channel Mode, Logic 1 = Dual

Channel Mode.)

*1******

Bit 6—Output Mode. Determine Interleaved or Parallel Output Mode.

(Logic 0 = Interleaved Mode, Logic 1 = Parallel Mode.)

**0*****

Bit 5—A/B Invert. Determines which port outputs the first data byte

after Hsync. (Logic 0 = A Port, Logic 1 = B Port.)

***1****

Bit 4—Hsync Output polarity. (Logic 0 = Logic High Sync, Logic 1 =

Logic Low Sync.)

****1***

Bit 3—Vsync Output Invert. (Logic 0 = No Invert, Logic 1 = Invert.)