ADF4355

Data Sheet

Rev. A | Page 28 of 35

DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10

DB9

DB8

DB7

DB6

DB5

DB4

DB3

DB2

DB1

DB0

00

0

00

RESERVED

CONTROL

BITS

1

1

0

000

0

0

0

0

C3(0) C2(1) C1(0)

C4(1)

0

0

0

AE1

AE2

AD1

AD2

AD3

AD4

AD5

AD6

AD7

AD8

ADC

CLOCK DIVIDER

AD8

AD7

..........

..........

..........

..........

..........

..........

..........

..........

..........

..........

AD2

AD1

ADC CLK DIV

00

0

1

1

00

1

0

2

..

.

.

.

..

.

.

.

..

.

.

.

11

0

0

252

11

0

1

253

11

1

0

254

11

1

1

255

AE1

ADC

0DISABLED

1

ENABLED

AE2

ADC CONVERSION

0

DISABLED

1

ENABLED

Figure 40. Register 10

DB31 DB30 DB29 DB28 DB27 DB26 DB25 DB24 DB23 DB22 DB21 DB20 DB19 DB18 DB17 DB16 DB15 DB14 DB13 DB12 DB11 DB10 DB9 DB8

DB7

DB6

DB5 DB4

DB3

DB2

DB1

DB0

0

0

00

0

RESERVED

CONTROL

BITS

01

1

0

0

00

1

00

1

10

0

0

0

0

0

0

0

C3(0) C2(1) C1(1)

C4(1)

0

0

0

Figure 41. Register 11 (0x0061300B)

REGISTER 10

Control Bits

With Bits[C4:C1] set to 1010, Register 10 is programmed.

Figure 40 shows the input data format for programming this

register.

Reserved

Bits[DB31:DB14] are reserved. Bits[DB23:DB22] must be set to

11, but all other bits in this range must be set to 0.

ADC Clock Divider (ADC_CLK_DIV)

An on-board analog-to-digital converter (ADC) determines the

environment. The ADC ensures that the initial tuning voltage

in any application is chosen correctly to avoid any temperature

drift issues.

The ADC uses a clock that is equal to the output of the R counter

(or the PFD frequency) divided by ADC_CLK_DIV.

AD8 to AD1 (Bits[DB13:DB6]) set the value of this divider. On

power-up, the R counter is not programmed; however, in these

power-up cases, it defaults to R = 1.

Choose the ADC_CLK_DIV value such that

where ceiling() is a function to round up to the nearest integer.

so that the ADC clock frequency is 99.417 kHz. If ADC_CLK_DIV

is greater than 255, set it to 255.

ADC Conversion Enable

AE2 (Bit DB5) ensures that the ADC performs a conversion

when a write to Register 10 is performed. It is recommended to

enable this mode.

ADC Enable

AE1 (Bit DB4), when set to 1, powers up the ADC for the

always use this function.

REGISTER 11

The bits in this register are reserved and must be programmed as

described in Figure 41, using a hexadecimal word of 0x0061300B.