| поискавой системы для электроныых деталей |
|
JS28F128P30TF75A датащи(PDF) 35 Page - Micron Technology |
|
|
|||||||||||||||||||||||||||||
JS28F128P30TF75A датащи(HTML) 35 Page - Micron Technology |
|
35 / 90 page ![]() Datasheet Apr 2010 35 Order Number:208033-02 P30-65nm SBC RCR contents can be examined using the Read Device Identifier command, and then reading from offset 0x05 (see Section 7.2, “Read Device Identifier” on page 22). Upon power-up or exit from reset, the RCR defaults to asynchronous mode. The RCR is shown in Table 13. The following sections describe each RCR bit function. 11.2.1 Read Mode (RCR.15) The Read Mode (RM) bit selects synchronous burst-mode or asynchronous page-mode operation for the device. When the RM bit is set, asynchronous page mode is selected (default). When RM is cleared, synchronous burst mode is selected. Table 13: Read Configuration Register Description Read Configuration Register (RCR) Read Mode RES Latency Count WAIT Polarity Data Output Config WAIT Delay Burst Seq CLK Edge RES RES Burst Wrap Burst Length RM R LC[3:0] WP DOC WD BS CE R R BW BL[2:0] 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit Name Description 15 Read Mode (RM) 0 = Synchronous burst-mode read 1 = Asynchronous page-mode read (default) 14 Reserved (R) Set to 0. This bit cannot be altered by customer. 13:11 Latency Count (LC[2:0]) 000 =Code 0 reserved 001 =Code 1 reserved 010 =Code 2 011 =Code 3 100 =Code 4 101 =Code 5 110 =Code 6 111 =Code 7(default) 10 WAIT Polarity (WP) 0 =WAIT signal is active low 1 =WAIT signal is active high (default) 9 Data Output Configuration (DOC) 0 =Data held for a 1-clock data cycle 1 =Data held for a 2-clock data cycle (default) 8 WAIT Delay (WD) 0 =WAIT deasserted with valid data 1 =WAIT deasserted one data cycle before valid data (default) 7 Burst Sequence (BS) 0 =Reserved 1 =Linear (default) 6 Clock Edge (CE) 0 = Falling edge 1 = Rising edge (default) 5:4 Reserved (R) Set to 0. This bit cannot be altered by customer. 3 Burst Wrap (BW) 0 =Wrap; Burst accesses wrap within burst length set by BL[2:0] 1 =No Wrap; Burst accesses do not wrap within burst length (default) 2:0 Burst Length (BL[2:0]) 001 =4-word burst 010 =8-word burst 011 =16-word burst 111 =Continuous-word burst (default) (Other bit settings are reserved) |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |