PIC16F87 datasheet(110/230 Pages) MICROCHIP

110 / 230 page

PIC16F87/88

DS30487D-page 110

 2002-2013 Microchip Technology Inc.

11.3.2

AUSART SYNCHRONOUS MASTER

RECEPTION

Once Synchronous mode is selected, reception is

enabled

setting

either

enable

bit

SREN

(RCSTA<5>), or enable bit CREN (RCSTA<4>). Data is

sampled on the RB2/SDO/RX/DT pin on the falling

edge of the clock. If enable bit SREN is set, then only a

single word is received. If enable bit CREN is set, the

reception is continuous until CREN is cleared. If both

bits are set, CREN takes precedence.

After clocking the last bit, the received data in the

Receive Shift Register (RSR) is transferred to the

RCREG register (if it is empty). When the transfer is

complete, interrupt flag bit, RCIF (PIR1<5>), is set. The

actual interrupt can be enabled/disabled by setting/

clearing enable bit RCIE (PIE1<5>).

Flag bit RCIF is a read-only bit which is reset by the

hardware. In this case, it is reset when the RCREG

double-buffered register (i.e., it is a two-deep FIFO). It is

possible for two bytes of data to be received and

transferred to the RCREG FIFO and a third byte to begin

shifting into the RSR register. On the clocking of the last

bit of the third byte, if the RCREG register is still full, then

Overrun Error bit, OERR (RCSTA<1>), is set. The word

in the RSR will be lost. The RCREG register can be read

twice to retrieve the two bytes in the FIFO. Bit OERR has

to be cleared in software (by clearing bit CREN). If bit

OERR is set, transfers from the RSR to the RCREG are

inhibited, so it is essential to clear bit OERR if it is set.

The ninth receive bit is buffered the same way as the

receive data. Reading the RCREG register will load bit

RX9D with a new value, therefore, it is essential for the

user to read the RCSTA register, before reading

RCREG, in order not to lose the old RX9D information.

When setting up a synchronous master reception:

Initialize the SPBRG register for the appropriate

baud rate (Section 11.1 “AUSART Baud Rate

Generator (BRG)”).

Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

Ensure bits CREN and SREN are clear.

If interrupts are desired, then set enable bit

RCIE.

If 9-bit reception is desired, then set bit RX9.

If a single reception is required, set bit SREN.

For continuous reception, set bit CREN.

Interrupt flag bit, RCIF, will be set when

reception is complete and an interrupt will be

generated if enable bit, RCIE, was set.

Read the RCSTA register to get the ninth bit (if

enabled) and determine if any error occurred

during reception.

Read the 8-bit received data by reading the

RCREG register.

10. If any error occurred, clear the error by clearing

bit CREN.

11. If using interrupts, ensure that GIE and PEIE

(bits 7 and 6) of the INTCON register are set.

TABLE 11-11: REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on:

POR, BOR

Value on

all other

Resets

0Bh, 8Bh,

10Bh,18Bh

INTCON

GIE

PEIE

TMR0IE INT0IE

RBIE

TMR0IF

INT0IF

RBIF

0000 000x

0000 000u

0Ch

PIR1

—

ADIF(1)

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

-000 0000

18h

RCSTA

SPEN

RX9

SREN

CREN

ADDEN

FERR

OERR

RX9D

0000 000x

1Ah

RCREG

AUSART Receive Data Register

0000 0000

8Ch

PIE1

—

ADIE(1)

RCIE

TXIE

SSPIE

CCP1IE

TMR2IE

TMR1IE

-000 0000

98h

TXSTA

CSRC

TX9

TXEN

SYNC

—

BRGH

TRMT

TX9D

0000 -010

99h

SPBRG

Baud Rate Generator Register

0000 0000

Legend:

= unknown, - = unimplemented, read as ‘0’. Shaded cells are not used for synchronous master reception.

Note

This bit is only implemented on the PIC16F88. The bit will read ‘0’ on the PIC16F87.

PIC16F87 датащи(PDF) 110 Page - Microchip Technology

PIC16F87 датащи(HTML) 110 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL