S29GL01GP datasheet(79/81 Pages) SPANSION

79 / 81 page

October 22, 2012 S29GL-P_00_A14

S29GL-P MirrorBit® Flash Family

Data

She e t

Revision A8 (November 28, 2007)

Ordering Information

New commercial operating temperature option

Operating Ranges

New operating temperature range

Revision A9 (February 15, 2008)

Electrical Specification

Modified Test Conditions

Erase and Programming Performance

Chip Program Time: removed comment

Sector Protection Command Definition,

x16 Table

Corrected Lock Register “Read” address

Advance Information on S29GL-R 65

nm MirrorBit Hardware Reset (RESET#)

and Power-up Sequence

Power-Up Sequence Timings Table: modified Note 2 - reduced timing from 500 µs to 300 µs

Revision A10 (March 19, 2008)

Global

Changed document status to Full Production.

DC Characteristics

Changed Max values for Input Load Current (ILI)

Sector Protection Command Definitions

(x16 & x8 tables)

Changed Lock Register Read command from “DATA” to “RD”

Revision A11 (June 11, 2008)

Ordering Information

Revised Commercial temperature range

Figure: Write Operation Status

Flowchart

Updated flowchart

Revision A12 (November 20, 2009)

Table Input/Output Descriptions

Removed RFU description

Figure 64-ball Fortified Ball Grid Array

Changed all RFU pins to NC pins

Figure 56-pin Standard TSOP (Top

View)

Changed all RFU pins to NC pins

Table Autoselect Exit

Changed cycle description to Auto Select Exit Command

Table Chip Erase

Changed address of last C source code command from 0x000h to 0x555h

Erase Suspend/Erase Resume

Changed first paragraph, second sentence to sector address is “don't care” for Erase Suspend

Changed sixth paragraph, second sentence to sector address is “don't care” for Erase Suspend

Tables

Program Suspend

Program Resume

Unlock Bypass Entry

Unlock Bypass Program

Unlock Bypass Reset

Added Byte Address to tables

Unlock Bypass

Third paragraph, first sentence added unlock bypass Sector Erase and unlock bypass Chip Erase

as valid commands

Changed paragraph, third sentence to sector address of exit command is “don't care”.

Writing Commands/Command

Sequence

Changed tables listed in fourth sentence to Table 6.1-6.4

WP#/ACC Method

Changed table listed in Note section to 11.2.

Secured Silicon Sector Entry/Exit

Command Sequence

Added source code for program under Table 10.3

Table Secured Silicon Sector Exit

Changed Byte and Word addresses of Exit Cycle to “XXXh”

Figure Test Setup

Changed test setup to show only a load of CL

Table Test Specification

Removed Output Load Test Condition

Table S29GL-P Erase and Program

Operations

Removed tGHWL

Table S29GL-P Alternate CE#

Controlled Erase and Program

Operations

Changed description of tGHEL to (OE# High to CE# Low)

Change Note 2 to “DC Characteristics”

Section

Description

S29GL01GP датащи(PDF) 79 Page - SPANSION

S29GL01GP датащи(HTML) 79 Page - SPANSION

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81

датащи скачать

ссылки URL