HT68F13 datasheet(91/161 Pages) HOLTEK

91 / 161 page

TM1C2 Register

Bit

76543210

Name

T1BM1

T1BM0

T1BIO1

T1BIO0

T1BOC

T1BPOL

T1PWM1

T1PWM0

R/W

POR

00000000

Bit 7~6

T1BM1~T1BM0: Select TM1 CCRB Operating Mode

00: Compare Match Output Mode

01: Capture Input Mode

10: PWM Mode or Single Pulse Output Mode

11: Timer/Counter mode

These bits setup the required operating mode for the TM. To ensure reliable operation the TM

should be switched off before any changes are made to the T1BM1 and T1BM0 bits. In the

Timer/Counter Mode, the TM output pin control must be disabled.

Bit 5~4

T1BIO1~T1BIO0: Select TP1B_0, TP1B_1, TP1B_2 output function

Compare Match Output Mode

00: No change

01: Output low

10: Output high

11: Toggle output

PWM Mode/Single Pulse Output Mode

00: PWM output inactive state

01: PWM output active state

10: PWM output

11: Single pulse output

Capture Input Mode

00: Input capture at rising edge of TP1B_0, TP1B_1, TP1B_2

01: Input capture at falling edge of TP1B_0, TP1B_1, TP1B_2

10: Input capture at falling/rising edge of TP1B_0, TP1B_1, TP1B_2

11: Input capture disabled

Timer/counter Mode

Unused

These two bits are used to determine how the TM output pin changes state when a certain

condition is reached. The function that these bits select depends upon in which mode the

TM is running.

In the Compare Match Output Mode, the T1BIO1 and T1BIO0 bits determine how the TM

output pin changes state when a compare match occurs from the Comparator A. The TM output

pin can be setup to switch high, switch low or to toggle its present state when a compare match

occurs from the Comparator A. When the bits are both zero, then no change will take place on

the output. The initial value of the TM output pin should be setup using the T1BOC bit in the

TM1C2 register. Note that the output level requested by the T1BIO1 and T1BIO0 bits must be

different from the initial value setup using the T1BOC bit otherwise no change will occur on the

TM output pin when a compare match occurs. After the TM output pin changes state it can be

reset to its initial level by changing the level of the T1ON bit from low to high.

In the PWM Mode, the T1BIO1 and T1BIO0 bits determine how the TM output pin changes

state when a certain compare match condition occurs. The PWM output function is modified by

changing these two bits. It is necessary to change the values of the T1BIO1 and T1BIO0 bits only

after the TM has been switched off. Unpredictable PWM outputs will occur if the T1BIO1 and

T1BIO0 bits are changed when the TM is running

Rev. 1.10

February 9, 2011

HT68F13/HT68F14/HT68F15

Enhanced I/O Flash Type MCU

HT68F13 датащи(PDF) 91 Page - Holtek Semiconductor Inc

HT68F13 датащи(HTML) 91 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL