HT68F13 datasheet(90/161 Pages) HOLTEK

90 / 161 page

Timer/counter Mode

Unused

These two bits are used to determine how the TM output pin changes state when a certain

condition is reached. The function that these bits select depends upon in which mode the TM is

running.

In the Compare Match Output Mode, the T1AIO1 and T1AIO0 bits determine how the TM

output pin changes state when a compare match occurs from the Comparator A. The TM output

pin can be setup to switch high, switch low or to toggle its present state when a compare match

occurs from the Comparator A. When the bits are both zero, then no change will take place on

the output. The initial value of the TM output pin should be setup using the T1AOC bit in the

TM1C1 register. Note that the output level requested by the T1AIO1 and T1AIO0 bits must be

different from the initial value setup using the T1AOC bit otherwise no change will occur on the

TM output pin when a compare match occurs. After the TM output pin changes state it can be

reset to its initial level by changing the level of the T1ON bit from low to high.

In the PWM Mode, the T1AIO1 and T1AIO0 bits determine how the TM output pin changes state

when a certain compare match condition occurs. The PWM output function is modified by

changing these two bits. It is necessary to change the values of the T1AIO1 and T1AIO0 bits

only after the TM has been switched off. Unpredictable PWM outputs will occur if the T1AIO1

and T1AIO0 bits are changed when the TM is running

Bit 3

T1AOC: TP1A Output control bit

Compare Match Output Mode

0: Initial low

1: Initial high

PWM Mode/ Single Pulse Output Mode

0: Active low

1: Active high

This is the output control bit for the TM output pin. Its operation depends upon whether TM is

being used in the Compare Match Output Mode or in the PWM Mode/ Single Pulse Output Mode.

It has no effect if the TM is in the Timer/Counter Mode. In the Compare Match Output Mode it

determines the logic level of the TM output pin before a compare match occurs. In the PWM

Mode it determines if the PWM signal is active high or active low.

Bit 2

T1APOL: TP1A Output polarity Control

0: Non-invert

1: Invert

This bit controls the polarity of the TP1A output pin. When the bit is set high the TM output pin

will be inverted and not inverted when the bit is zero. It has no effect if the TM is in the

Timer/Counter Mode.

Bit 1

T1CDN: TM1 Counter count up or down flag

0: Count up

1: Count down

Bit 0

T1CCLR: Select TM1 Counter clear condition

0: TM1 Comparator P match

1: TM1 Comparator A match

This bit is used to select the method which clears the counter. Remember that the Enhanced

TM contains three comparators, Comparator A, Comparator B and Comparator P, but only

Comparator A or Comparator Pan be selected to clear the internal counter. With the T1CCLR bit

set high, the counter will be cleared when a compare match occurs from the Comparator A.

When the bit is low, the counter will be cleared when a compare match occurs from the

Comparator P or with a counter overflow. A counter overflow clearing method can only be

implemented if the CCRP bits are all cleared to zero. The T1CCLR bit is not used in the

Single Pulse or Input Capture Mode.

HT68F13/HT68F14/HT68F15

Enhanced I/O Flash Type MCU

Rev. 1.10

February 9, 2011

HT68F13 датащи(PDF) 90 Page - Holtek Semiconductor Inc

HT68F13 датащи(HTML) 90 Page - Holtek Semiconductor Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL