ATmega32A datasheet(19/352 Pages) ATMEL

19 / 352 page

8155B–AVR–07/09

ATmega32A

7.4

EEPROM Data Memory

The ATmega32A contains 1024 bytes of data EEPROM memory. It is organized as a separate

data space, in which single bytes can be read and written. The EEPROM has an endurance of at

least 100,000 write/erase cycles. The access between the EEPROM and the CPU is described

in the following, specifying the EEPROM Address Registers, the EEPROM Data Register, and

the EEPROM Control Register.

“Memory Programming” on page 266 contains a detailed description on EEPROM Programming

in SPI, JTAG, or Parallell Programming mode.

7.4.1

EEPROM Read/Write Access

The EEPROM Access Registers are accessible in the I/O space.

The write access time for the EEPROM is given in Table 7-1. A self-timing function, however,

lets the user software detect when the next byte can be written. If the user code contains instruc-

tions that write the EEPROM, some precautions must be taken. In heavily filtered power

supplies, V

CC is likely to rise or fall slowly on Power-up/down. This causes the device for some

period of time to run at a voltage lower than specified as minimum for the clock frequency used.

See “Preventing EEPROM Corruption” on page 19 for details on how to avoid problems in these

situations.

In order to prevent unintentional EEPROM writes, a specific write procedure must be followed.

Refer to the description of the EEPROM Control Register for details on this.

When the EEPROM is read, the CPU is halted for four clock cycles before the next instruction is

executed. When the EEPROM is written, the CPU is halted for two clock cycles before the next

instruction is executed.

7.4.2

EEPROM Write During Power-down Sleep Mode

When entering Power-down Sleep mode while an EEPROM write operation is active, the

EEPROM write operation will continue, and will complete before the Write Access time has

passed. However, when the write operation is completed, the Oscillator continues running, and

as a consequence, the device does not enter Power-down entirely. It is therefore recommended

to verify that the EEPROM write operation is completed before entering Power-down.

7.4.3

Preventing EEPROM Corruption

During periods of low V

CC, the EEPROM data can be corrupted because the supply voltage is

too low for the CPU and the EEPROM to operate properly. These issues are the same as for

board level systems using EEPROM, and the same design solutions should be applied.

An EEPROM data corruption can be caused by two situations when the voltage is too low. First,

a regular write sequence to the EEPROM requires a minimum voltage to operate correctly. Sec-

ondly, the CPU itself can execute instructions incorrectly, if the supply voltage is too low.

ATmega32A датащи(PDF) 19 Page - ATMEL Corporation

ATmega32A датащи(HTML) 19 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL