ATtiny25 datasheet(34/196 Pages) ATMEL

34 / 196 page

7598H–AVR–07/09

ATtiny25/45/85

• Bit 2- PRTIM0: Power Reduction Timer/Counter0

Writing a logic one to this bit shuts down the Timer/Counter0 module. When the Timer/Counter0

is enabled, operation will continue like before the shutdown.

• Bit 1 - PRUSI: Power Reduction USI

Writing a logic one to this bit shuts down the USI by stopping the clock to the module. When

waking up the USI again, the USI should be re initialized to ensure proper operation.

• Bit 0 - PRADC: Power Reduction ADC

Writing a logic one to this bit shuts down the ADC. The ADC must be disabled before shut down.

The analog comparator cannot use the ADC input MUX when the ADC is shut down.

7.7

Minimizing Power Consumption

There are several issues to consider when trying to minimize the power consumption in an AVR

controlled system. In general, sleep modes should be used as much as possible, and the sleep

mode should be selected so that as few as possible of the device’s functions are operating. All

functions not needed should be disabled. In particular, the following modules may need special

consideration when trying to achieve the lowest possible power consumption.

7.7.1

Analog to Digital Converter

If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-

abled before entering any sleep mode. When the ADC is turned off and on again, the next

conversion will be an extended conversion. Refer to “Analog to Digital Converter” on page 111

for details on ADC operation.

7.7.2

Analog Comparator

When entering Idle mode, the Analog Comparator should be disabled if not used. When entering

ADC Noise Reduction mode, the Analog Comparator should be disabled. In the other sleep

modes, the Analog Comparator is automatically disabled. However, if the Analog Comparator is

set up to use the Internal Voltage Reference as input, the Analog Comparator should be dis-

abled in all sleep modes. Otherwise, the Internal Voltage Reference will be enabled,

independent of sleep mode. Refer to “Analog Comparator” on page 108 for details on how to

configure the Analog Comparator.

7.7.3

Brown-out Detector

If the Brown-out Detector is not needed in the application, this module should be turned off. If the

Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep modes,

and hence, always consume power. In the deeper sleep modes, this will contribute significantly

to the total current consumption. Refer to “Brown-out Detection” on page 38 for details on how to

configure the Brown-out Detector.

7.7.4

Internal Voltage Reference

The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the

Analog Comparator or the ADC. If these modules are disabled as described in the sections

above, the internal voltage reference will be disabled and it will not be consuming power. When

turned on again, the user must allow the reference to start up before the output is used. If the

reference is kept on in sleep mode, the output can be used immediately. Refer to “Internal Volt-

age Reference” on page 40 for details on the start-up time.

ATtiny25 датащи(PDF) 34 Page - ATMEL Corporation

ATtiny25 датащи(HTML) 34 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL