| поискавой системы для электроныых деталей |
|
MFS5600AMBAFES датащи(PDF) 19 Page - NXP Semiconductors |
|
|
|||||||||||||||||||||||||||||
MFS5600AMBAFES датащи(HTML) 19 Page - NXP Semiconductors |
|
19 / 118 page ![]() NXP Semiconductors FS5600 Automotive buck regulator and controller with voltage monitors and watchdog timer OTP_SW1_VOLT[7:0] Vout Setting (V) 11100xxx 5.8 V - 6.15 V with external resistor divider 11101xxx 6.2 V - 6.55 V with external resistor divider 11110xxx 6.6 V - 6.95 V with external resistor divider 11111xxx 7 V - 8 V with external resistor divider Table 10. OTP_SW1_VOLT[7:0] selection...continued 11.3.2 PFM and pulse skipping operation At a high VIN/VOUT ratio with high switching frequency, the controller may start to skip pulses to maintain regulation. The minimum on-time of the high side FET is programmable via the OTP_SW1_MIN_TON[1:0] bits. OTP_SW1_MIN_TON[1:0] = 0b01 is the recommended default value that is optimal for most applications. OTP_SW1_MIN_TON[1:0] SW1 minimum on-time (ns) 00 40 01 60 (recommended) 10 80 11 100 Table 11. OTP_SW1_MIN_TON[1:0] selection In addition, the controller starts to switch at half of the selected frequency when the VIN/VOUT ratio is above 6. This allows reduced ripple operation compared to pulse-skipping. 11.3.3 PFM operation When the OTP_MODE_SYNCINB bit = 0, the MODE/SYNCIN pin is configured as a SYNCIN input. In this case, the switching mode of SW1 can be selected using the SW1_MODE[1:0] bits. Default value of SW1_MODE[1:0] is loaded from OTP_SW1_MODE[1:0]. OTP_SW1_MODE[1:0] SW1_MODE[1:0] SW1 operating mode 00 PFM 01 Reserved. Do not use. 10 Reserved. Do not use. 11 PWM Table 12. SW1_MODE[1:0] selection. When the OTP_MODE_SYNCINB bit = 1, the MODE/SYNCIN pin is configured as a MODE input that can be used to select the operating mode of SW1 between PWM (MODE = 0) and PFM (MODE = 1). To avoid conflicts between the pin and register bits, do not use SW1_MODE[1:0] to change the operating mode. On-time of the pulses in PFM mode is configurable using the OTP_SW1_PFM_TON[1:0] bits. OTP_SW1_PFM_TON[1:0] = 0b10 offers a good compromise between quiescent current and the output ripple for most applications. OTP_SW1_PFM_TON[1:0] SW1 PFM on-time (ns) 00 160 Table 13. OTP_SW1_PFM_TON[1:0] selection FS5600 All information provided in this document is subject to legal disclaimers. © 2024 NXP B.V. All rights reserved. Product data sheet Rev. 4 — 29 April 2024 19 / 118 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |