HDMP-1012 datasheet(9/42 Pages) HP

9 / 42 page

581

Clock Select

The Clock Select accepts the

high speed digital signal from

the VCO and outputs an

internal high speed serial clock.

The VCO frequency is divided,

based on the DIV1/DIV0 inputs,

to the input signal’s frequency

range. The Clock Select output,

accessible through BCLK, is an

internal serial clock. It is phase

and frequency locked to the

incoming signal. This internal

serial clock is used by the Input

Sampler to sample the data. It

is also used by the Clock

Generator to generate the

recovered frame rate clock.

By setting TCLKSEL high, the

user may input an external high

speed serial clock at TCLK. The

Clock Select accepts this signal

and directly outputs it as the

internal serial clock.

Clock Generator

The Clock Generator accepts the

serial clock generated from the

Clock Select and generates the

frame rate clock, based on the

setting of M20SEL. If M20SEL

is asserted, the incoming

encoded data frame is expected

to be 24 bits wide (20 data bits

and 4 control bits). The master

transition in the control section

of encoded data stream is

expected every 24 bits, and used

to ensure proper frame syn-

chronization of the output frame

clock, STRBOUT.

Input Sampler

The serial input signal is

converted into a serial bit

stream, using the extracted

internal serial clock from the

Clock Select. This output is

sent to the frame demux.

Frame Demux

The Frame Demux demulti-

plexes the serial bit stream from

the Input Sampler into a 20 or

24 bit wide parallel data word,

based on the setting of M20SEL.

The most significant 4 bits are

sent to the C-Field Decoder,

while the remaining 16 or 20

bits are sent to the D-Field

Decoder.

C-Field Decoder

The C-Field Decoder accepts the

control information from the

Frame Demux and determines

what kind of frame is being

received and whether or not it

has to be inverted. The control

bits are sent to the State

Machine for error checking.

The decoded information is sent

to the D-Field Decoder. CAV* is

set low if the incoming frame is

control data. DAV* is set low if

the information is data. If

neither DAV* nor CAV* is set

low, then the incoming frame is

expected to be a fill frame. If

FLAGSEL is asserted, the

FLAG bit is restored to its

original form. Otherwise, FLAG

is used to differentiate between

the even and odd frames in

Double Frame Mode. For more

information about this, refer to

Double Frame Mode

D-Field Decoder

The D-Field Decoder accepts the

data field of the incoming data

frame from the Frame Demux.

Based on information from the

C-Field Decoder, which deter-

mines what type of data is being

received, the D-Field Decoder

restores the parallel data back

to its original form.

State Machine

The State Machine is used in

full duplex mode to perform the

functions of link startup, link

maintenance, and error check-

ing. By setting the SMRST0*

and SMRST1* low, the user,

too, can reset the state machine

and initiate link startup.

SMRST1* is usually connected

to the transmitters LOCKED

output. STAT1 and STAT0

denote the current state of link

during startup. ACTIVE is an

input normally driven by the

STAT1 and STAT0 outputs.

This ACTIVE input is retimed

by STRBOUT and presented to

the user as LINKRDY*.

LINKRDY* is an active low

output that indicates when the

link is ready to transmit data.

Refer to The State Machine

Handshake Protocol

section on

page 600 for more details.

HDMP-1012 датащи(PDF) 9 Page - Agilent(Hewlett-Packard)

HDMP-1012 датащи(HTML) 9 Page - Agilent(Hewlett-Packard)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

датащи скачать

ссылки URL