MPC8306EC datasheet(48/76 Pages) FREESCALE

48 / 76 page

MPC8306 PowerQUICC II Pro Integrated Communications Processor Family Hardware Specifications, Rev. 0

Freescale Semiconductor

JTAG

Figure 36 provides the AC test load for TDO and the boundary-scan outputs of the MPC8306.

Figure 36. AC Test Load for the JTAG Interface

Figure 37 provides the JTAG clock input timing diagram.

Figure 37. JTAG Clock Input Timing Diagram

Figure 38 provides the TRST timing diagram.

Figure 38. TRST Timing Diagram

Output hold times:

Boundary-scan data

TDO

tJTKLDX

tJTKLOX

—

JTAG external clock to output high impedance:

Boundary-scan data

TDO

tJTKLDZ

tJTKLOZ

5, 6

Notes:

1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.

The output timings are measured at the pins. All output timings assume a purely resistive 50-

load (see Figure 36).

Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.

2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)(reference)(state) for

inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device

timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K)

going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals

(D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference

symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the

latter convention is used with the appropriate letter: R (rise) or F (fall).

3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.

4. Non-JTAG signal input timing with respect to tTCLK.

5. Non-JTAG signal output timing with respect to tTCLK.

6. Guaranteed by design and characterization.

Table 51. JTAG AC Timing Specifications (Independent of SYS_CLK_IN)1 (continued)

At recommended operating conditions (see Table 2).

Parameter

Symbol2

Min

Max

Unit

Notes

Output

Z0 = 50 

OVDD/2

RL = 50 

JTAG

tJTKHKL

tJTGR

External Clock

tJTG

tJTGF

VM = Midpoint Voltage (OVDD/2)

TRST

VM = Midpoint Voltage (OVDD/2)

tTRST

MPC8306EC датащи(PDF) 48 Page - Freescale Semiconductor, Inc

MPC8306EC датащи(HTML) 48 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

датащи скачать

ссылки URL