DSPIC30F2010 datasheet(49/202 Pages) MICROCHIP

49 / 202 page

DS70118J-page 49

dsPIC30F2010

7.0

DATA EEPROM MEMORY

The Data EEPROM Memory is readable and writable

during normal operation over the entire VDD range. The

data EEPROM memory is directly mapped in the

program memory address space.

The four SFRs used to read and write the program

Flash memory are used to access data EEPROM

memory as well. As described in Section 6.0 “Flash

Program Memory”, these registers are:

•NVMCON

• NVMADR

• NVMADRU

• NVMKEY

The EEPROM data memory allows read and write of

single words and 16-word blocks. When interfacing to

data memory, NVMADR, in conjunction with the

NVMADRU register, is used to address the EEPROM

location

being

accessed.

TBLRDL

and

TBLWTL

instructions are used to read and write data EEPROM.

The dsPIC30F devices have up to 1 Kbyte of data

EEPROM, with an address range from 0x7FFC00 to

0x7FFFFE.

A word write operation should be preceded by an erase

of the corresponding memory location(s). The write

typically requires 2 ms to complete, but the write time

will vary with voltage and temperature.

A program or erase operation on the data EEPROM

does not stop the instruction flow. The user is respon-

sible for waiting for the appropriate duration of time

before initiating another data EEPROM write/erase

operation. Attempting to read the data EEPROM while

a programming or erase operation is in progress results

in unspecified data.

Control bit WR initiates write operations, similar to pro-

gram Flash writes. This bit cannot be cleared, only set,

in software. This bit is cleared in hardware at the com-

pletion of the write operation. The inability to clear the

WR bit in software prevents the accidental or

premature termination of a write operation.

The WREN bit, when set, will allow a write operation.

On power-up, the WREN bit is clear. The WRERR bit is

set when a write operation is interrupted by a MCLR

Reset, or a WDT Time-out Reset, during normal oper-

ation. In these situations, following Reset, the user can

check the WRERR bit and rewrite the location. The

address register NVMADR remains unchanged.

7.1

Reading the Data EEPROM

A TBLRD instruction reads a word at the current pro-

gram word address. This example uses W0 as a

pointer to data EEPROM. The result is placed in

EXAMPLE 7-1:

DATA EEPROM READ

Note:

This data sheet summarizes features of

this group of dsPIC30F devices and is not

intended to be a complete reference

source. For more information on the CPU,

peripherals,

descriptions

and

general device functionality, refer to the

“dsPIC30F Family Reference Manual”

(DS70046). For more information on the

device instruction set and programming,

refer to the “16-bit MCU and DSC Pro-

grammer’s

Reference

Manual”

(DS70157).

Note:

Interrupt flag bit NVMIF in the IFS0 regis-

ter is set when write is complete. It must

be cleared in software.

MOV

#LOW_ADDR_WORD,W0

; Init Pointer

MOV

#HIGH_ADDR_WORD,W1

MOV

W1,TBLPAG

TBLRDL

[ W0 ], W4

; read data EEPROM

DSPIC30F2010 датащи(PDF) 49 Page - Microchip Technology

DSPIC30F2010 датащи(HTML) 49 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL