DSPIC30F2010 datasheet(44/202 Pages) MICROCHIP

44 / 202 page

dsPIC30F2010

DS70118J-page 44

6.4

RTSP Operation

The dsPIC30F Flash program memory is organized

into rows and panels. Each row consists of 32 instruc-

tions, or 96 bytes. Each panel consists of 128 rows, or

4K x 24 instructions. RTSP allows the user to erase one

row (32 instructions) at a time and to program 32

instructions at one time. RTSP may be used to program

multiple program memory panels, but the table pointer

must be changed at each panel boundary.

Each panel of program memory contains write latches

that hold 32 instructions of programming data. Prior to

the actual programming operation, the write data must

be loaded into the panel write latches. The data to be

programmed into the panel is loaded in sequential

order into the write latches; instruction 0, instruction 1,

etc. The instruction words loaded must always be from

a 32 address boundary.

The basic sequence for RTSP programming is to set up

a table pointer, then do a series of TBLWT instructions

to load the write latches. Programming is performed by

setting the special bits in the NVMCON register. 32

TBLWTL

and four TBLWTH instructions are required to

load the 32 instructions. If multiple panel programming

is required, the table pointer needs to be changed and

the next set of multiple write latches written.

All of the table write operations are single word writes

(2 instruction cycles), because only the table latches

are written. A programming cycle is required for

programming each row.

The Flash program memory is readable, writable and

erasable during normal operation over the entire VDD

range.

6.5

Control Registers

The four SFRs used to read and write the program

Flash memory are:

•NVMCON

• NVMADR

• NVMADRU

• NVMKEY

6.5.1

NVMCON REGISTER

The NVMCON register controls which blocks are to be

erased, which memory type is to be programmed, and

the start of the programming cycle.

6.5.2

NVMADR REGISTER

The NVMADR register is used to hold the lower two

bytes of the effective address. The NVMADR register

captures the EA<15:0> of the last table instruction that

has been executed and selects the row to write.

6.5.3

NVMADRU REGISTER

The NVMADRU register is used to hold the upper byte

of the effective address. The NVMADRU register cap-

tures the EA<23:16> of the last table instruction that

has been executed.

6.5.4

NVMKEY REGISTER

NVMKEY is a write-only register that is used for write

protection. To start a programming or an erase

sequence, the user must consecutively write 0x55 and

0xAA to the NVMKEY register. Refer to Section 6.6

“Programming Operations” for further details.

Note:

The user can also directly write to the

NVMADR and NVMADRU registers to

specify a program memory address for

erasing or programming.

DSPIC30F2010 датащи(PDF) 44 Page - Microchip Technology

DSPIC30F2010 датащи(HTML) 44 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL