PIC24F04KA201 datasheet(46/224 Pages) MICROCHIP

46 / 224 page

PIC24F04KA201 FAMILY

DS39937B-page 44

Preliminary

5.2

RTSP Operation

The PIC24F Flash program memory array is organized

into rows of 32 instructions or 96 bytes. RTSP allows

the user to erase blocks of 1 row, 2 rows and 4 rows

(32, 64 and 128 instructions) at a time and to program

one row at a time. It is also possible to program single

words.

The 1-row (96 bytes), 2-row (192 bytes) and 4-row

(384 bytes) erase blocks and single row write block

(96 bytes) are edge-aligned, from the beginning of

program memory.

When data is written to program memory using TBLWT

instructions, the data is not written directly to memory.

Instead, data written using table writes is stored in holding

latches until the programming sequence is executed.

Any number of TBLWT instructions can be executed

and a write will be successfully performed. However,

32 TBLWT instructions are required to write the full row

of memory.

The basic sequence for RTSP programming is to set up

a Table Pointer, then do a series of TBLWT instructions to

load the buffers. Programming is performed by setting

the control bits in the NVMCON register.

Data can be loaded in any order and the holding

registers can be written to multiple times before

performing a write operation. Subsequent writes,

however, will wipe out any previous writes.

All of the table write operations are single-word writes

(two instruction cycles), because only the buffers are

written. A programming cycle is required for

programming each row.

5.3

Enhanced In-Circuit Serial

Programming

Enhanced ICSP uses an on-board bootloader, known

as the program executive, to manage the programming

process. Using an SPI data frame format, the program

executive can erase, program and verify program

memory. For more information on Enhanced ICSP, see

the device programming specification.

5.4

Control Registers

There are two SFRs used to read and write the

program Flash memory: NVMCON and NVMKEY.

The NVMCON register (Register 5-1) controls the

blocks that need to be erased, which memory type is to

be programmed and when the programming cycle

starts.

NVMKEY is a write-only register that is used for write

protection. To start a programming or erase sequence,

the user must consecutively write 55h and AAh to the

NVMKEY register. Refer to Section 5.5 “Programming

Operations”

for further details.

5.5

Programming Operations

A complete programming sequence is necessary for

programming or erasing the internal Flash in RTSP

mode. During a programming or erase operation, the

processor stalls (waits) until the operation is finished.

Setting the WR bit (NVMCON<15>) starts the

operation and the WR bit is automatically cleared when

the operation is finished.

Note:

Writing to a location multiple times without

erasing it is not recommended.

PIC24F04KA201 датащи(PDF) 46 Page - Microchip Technology

PIC24F04KA201 датащи(HTML) 46 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL