CDCE72010 datasheet(32/70 Pages) TI

32 / 70 page

CDCE72010

SCAS858 – JUNE 2008...................................................................................................................................................................................................... www.ti.com

SPI

RAM

POWER UP

BIT NAME

DESCRIPTION/FUNCTION

BIT

BLOCK

CONDITION

Address 0

Address 1

Address 2

Address 3

PRI_DIV2

Input Buffers

If set to 1 enables Primary Reference Divide by 2

EEPROM

SEC_DIV2

Input Buffers

If set to 1 enables Secondary Reference Divide by 2

EEPROM

FB Path Integer

When set to 0, FB divider is active

FB_DIS

EEPROM

Counter 32

When set to 1, FB divider is disabled

FB Path Integer

When set to 0, FB clock is CMOS type

FB_CML_SEL

EEPROM

Counter 32

When set to 1, FB clock is CML type and uses CML2CMOS converter in PLL

FB-Divider/

When set to 0, Input clock for FB not inverted (normal mode, low speed)

FB_INCLK_INV

Deterministic

EEPROM

When set to 1, Input clock for FB inverted (higher speed mode)

Blocks

FB_COUNT32_0

Feedback Counter Bit0

FB_COUNT32_1

Feedback Counter Bit1

FB_COUNT32_2

Feedback Counter Bit2

FB Path Integer

FB_COUNT32_3

Feedback Counter Bit3

EEPROM

Counter 32

FB_COUNT32_4

Feedback Counter Bit4

FB_COUNT32_5

Feedback Counter Bit5

FB_COUNT32_6

Feedback Counter Bit6

FB_PHASE0

Feedback Phase Adjust Bit0

FB_PHASE1

Feedback Phase Adjust Bit1

FB_PHASE2

Feedback Phase Adjust Bit2

FB Path Integer

FB_PHASE3

Feedback Phase Adjust Bit3

EEPROM

Counter 32

FB_PHASE4

Feedback Phase Adjust Bit4

FB_PHASE5

Feedback Phase Adjust Bit5

FB_PHASE6

Feedback Phase Adjust Bit6

If set to 0, PLL is in normal mode

PD_PLL

PLL

EEPROM

If set to 1, PLL is powered down

When set to 0, the VCXO Clock is selected for the Clock Tree and FB-Div and

Clock Tree and

FB_MUX_SEL

Det

Deterministic

EEPROM

See Table 6

When set to 1, the AUX Clock is selected for the Clock Tree and FB-Div and

Block

Det

OUT_MUX_SEL

Clock Tree

If Set to 0 it selects the VCXO Clock and if Set to 1 it selects the AUX Clock

EEPROM

See Table 6

Feed Back Path Selects FB/VCXO-Path when set to 0 (TI Test-GTME)

FB_SEL

Diagnostics

EEPROM

The Secondary Reference clock input is selected when set to 1 (TI Test-GTME)

NRESHAPE1

Reshapes the Reference Clock Signal 0, Disable Reshape 1

EEPROM

Reference

If set to 0 it enables short delay for fast operation

Selection Control

SEL_DEL1

EEPROM

If Set to 1 Long Delay recommended for Input References below 150Mhz

RESET_HOLD

Reset Circuitry

If set to 1 the RESET or HOLD pin acts as HOLD, set to 0 it acts as RESET

EEPROM

EPUNLOCK

Status

EEPROM Unlock

EEPROM

EPSTATUS

Status

EEPROM Status

EEPROM

Table 6. Output Buffers Source Feed, PLL Source Feed, and AUX IN/OUTPUT 9 Selection

FB_MUX_SEL

OUT_MUX_SEL

PLL FEED AND OUTPUTS FEED

AUX INPUT OR OUTPUT 9

VCXO::PLL, VCXO::Y0…Y9 and Deterministic Block

OUTPUT 9 is enabled

AUXIN::PLL, VCXO::Y0…Y8 and Deterministic Block

AUX IN is enabled

VCXO::PLL, AUXIN::Y0…Y8 and Deterministic Block

AUX IN is enabled

AUXIN::PLL, AUXIN::Y0…Y8 and Deterministic Block

AUX IN is enabled

Submit Documentation Feedback

Product Folder Link(s): CDCE72010

CDCE72010 датащи(PDF) 32 Page - Texas Instruments

CDCE72010 датащи(HTML) 32 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70

датащи скачать

ссылки URL