GRM0332C2A6R9DA01 datasheet(81/89 Pages) MURATA1

81 / 89 page

C02E.pdf

Nov.27,2017

Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.

282

Caution

2-1. In an Emergency

(1) If the equipment should generate smoke, ﬁre, or

smell, immediately turn o or unplug the

equipment.

If the equipment is not turned o or unplugged, the

hazards may be worsened by supplying continuous

power.

(2) In this type of situation, do not allow face and

hands to come in contact with the capacitor or

burns may be caused by the capacitor's high

temperature.

2-2. Disposal of Waste

When capacitors are disposed of, they must be burned

or buried by an industrial waste vendor with the

appropriate licenses.

2-3. Circuit Design

(1) Addition of Fail Safe Function

Capacitors that are cracked by dropping or bending

of the board may cause deterioration of the

insulation resistance, and result in a short.

If the circuit being used may cause an electrical

shock, smoke or ﬁre when a capacitor is shorted,

be sure to install fail-safe functions, such as a fuse,

to prevent secondary accidents.

(2) Capacitors used to prevent electromagnetic

interference in the primary AC side circuit, or as a

connection/insulation, must be a safety standard

certiﬁed product, or satisfy the contents stipulated

in the Electrical Appliance and Material Safety Law.

Install a fuse for each line in case of a short.

(3) The GJM, GMA, GMD, GQM, GR3, GRJ, GRM, KR3,

KRM, LLA, LLL, LLM, LLR, NFM and ZRB series are

not safety standard certiﬁed products.

2-4. Test Condition for AC Withstanding Voltage

(1) Test Equipment

Test equipment for AC withstanding voltage

should be made with equipment capable of

creating a wave similar to a 50/60Hz sine wave.

(2) Voltage Applied Method

The capacitor's lead or terminal should be ﬁrmly

connected to the output of the withstanding

voltage test equipment, and then the voltage

should be raised from near zero to the test

voltage.

If the test voltage is applied directly to the

capacitor without raising it from near zero, it

should be applied with the zero cross. *At the end

of the test time, the test voltage should be

reduced to near zero, and then capacitor's lead or

terminals should be taken o the output of the

withstanding voltage test equipment.

If the test voltage applied directly to the

capacitor without raising it from near zero, surge

voltage may occur and cause a defect.

*ZERO CROSS is the point where voltage sine wave

passes 0V. - See the ﬁgure at right -

2-5. Remarks

Failure to follow the cautions may result, worst case,

in a short circuit and smoking when the product is

used.

The above notices are for standard applications and

conditions. Contact us when the products are used in

special mounting conditions.

Select optimum conditions for operation as they

determine the reliability of the product aer

assembly.

The data herein are given in typical values, not

guaranteed ratings.

2. Other

Continued from the preceding page.

zero cross

Voltage sine wave

GRM0332C2A6R9DA01 датащи(PDF) 81 Page - Murata Manufacturing Co., Ltd

GRM0332C2A6R9DA01 датащи(HTML) 81 Page - Murata Manufacturing Co., Ltd

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89

датащи скачать

ссылки URL