ATMEGA640 datasheet(123/436 Pages) MICROCHIP

123 / 436 page

123

ATmega640/V-1280/V-1281/V-2560/V-2561/V [DATASHEET]

DS40002211A

Figure 16-7. Phase Correct PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches BOTTOM. The Interrupt Flag can

be used to generate an interrupt each time the counter reaches the BOTTOM value.

In phase correct PWM mode, the compare unit allows generation of PWM waveforms on the OC0x pins. Setting

the COM0x1:0 bits to two will produce a non-inverted PWM. An inverted PWM output can be generated by setting

the COM0x1:0 to three: Setting the COM0A0 bits to one allows the OC0A pin to toggle on Compare Matches if the

WGM02 bit is set. This option is not available for the OC0B pin (see Table 16-4 on page 127). The actual OC0x

value will only be visible on the port pin if the data direction for the port pin is set as output. The PWM waveform is

generated by clearing (or setting) the OC0x Register at the Compare Match between OCR0x and TCNT0 when the

counter increments, and setting (or clearing) the OC0x Register at Compare Match between OCR0x and TCNT0

when the counter decrements. The PWM frequency for the output when using phase correct PWM can be calcu-

lated by the following equation:

The N variable represents the prescale factor (1, 8, 64, 256, or 1024).

The extreme values for the OCR0A Register represent special cases when generating a PWM waveform output in

the phase correct PWM mode. If the OCR0A is set equal to BOTTOM, the output will be continuously low and if set

equal to MAX the output will be continuously high for non-inverted PWM mode. For inverted PWM the output will

have the opposite logic values.

At the very start of period 2 in Figure 16-7 OCnx has a transition from high to low even though there is no Compare

Match. The point of this transition is to guarantee symmetry around BOTTOM. There are two cases that give a

transition without Compare Match.

•

OCR0A changes its value from MAX, like in Figure 16-7. When the OCR0A value is MAX the OCn pin value is

the same as the result of a down-counting Compare Match. To ensure symmetry around BOTTOM the OCn

value at MAX must correspond to the result of an up-counting Compare Match.

•

The timer starts counting from a value higher than the one in OCR0A, and for that reason misses the Compare

Match and hence the OCn change that would have happened on the way up.

TOVn Interrupt Flag Set

OCnx Interrupt Flag Set

TCNTn

Period

OCnx

(COMnx1:0 = 2)

(COMnx1:0 = 3)

OCRnx Update

fOCnxPCPWM

fclk_I/O

N 510



------------------

ATMEGA640 датащи(PDF) 123 Page - Microchip Technology

ATMEGA640 датащи(HTML) 123 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL