IC-HTP datasheet(32/51 Pages) ICHAUS

32 / 51 page

prel

imin

ary

prel

imin

ary

iC-HTP

DUAL CW P-TYPE LASER DIODE DRIVER

Rev B1, Page 32/51

DC/DC CONVERTER OPTIMIZATION

iC-HTP provides a 6 bit configurable current at pin DCO

that can be used to trim the output voltage of a DC/DC

converter.

Possible application benefits with using DCO:

• DC/DC step down operation: regulation at voltages

lower than power supply

• DC/DC step up operation: regulation at voltages

higher than power supply

• Efficiency enhancement

RDCO

Addr. 0x1B; bit 5:0

R/W 0x02

0x00

No current

. . .

0x3F

Typ. 130 µA (cf. Electrical Characteristics No. D01)

Table 72: Digital current output register

The proposed applications can be demonstrated with

a standard DC/DC converter e.g. TPS63060DSC from

Texas Instruments. This converter allows an input volt-

age ranging from 2.5 V to 12 V and offers an output

voltages from 2.5 V to 8 V. It is capable of delivering up

to 2 A current, depending on the output voltage. Figure

18 shows a possible configuration.

TPS63060

2x10μF

0.1μF

3x22μF

1MEG

VIN

VAUX

PS/SYNC

GND

VOUT

PGND

Vin

2.5...12V

Vout

2.5...8V

1μH

1MEG

Figure 18: TPS63063 DC/DC converter from TI

DC/DC step down operation:

regulation at voltages lower than power supply

The resistors R1 and R2 in the feedback path allow

setting the desired output value Vout. The DC/DC con-

verter drives Vout pin in order to yield 0.5 V at feed-

back pin FB. The DCO output signal from iC-HTP is

connected to FB pin. The Vout is controlled with the

internal register RDCO from iC-HTP.

The DCO current into FB node controls the voltages

of the divider R1 and R2 and Vout changes in order to

maintain 0.5 V at FB pin. Selecting R1 and R2 needs

to consider:

• Resistors values:

R1 = R2( Vout

Vfb − 1)

• Current of the voltage divider should be high enough,

in comparison to the current from the pin DCO, to of-

fer acceptable resolution. The programmable current

resolution from register RDCO is 2 µA.

• DCO current into the voltage divider will lower Vout

voltage, Vout is 8 V when no current is present at

DCO.

Choosing R1 to 100 kΩ, the value of R2 can be calcu-

lated:

R2 = R1

Vout

Vfb −1

= 100k

0.5 −1

= 6.7kΩ

With this configuration the current through the voltage

divider is 75 µA at 8 V . The resolution of each RDCO

step is then 200 mV.

IC-HTP датащи(PDF) 32 Page - IC-Haus GmbH

IC-HTP датащи(HTML) 32 Page - IC-Haus GmbH

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51

датащи скачать

ссылки URL