CLC5903 datasheet(17/29 Pages) NSC

17 / 29 page

www.national.com

decreases relative to the output sample rate, the CIC droop

compensation performed by F1 may no longer be required.

Overall Channel Gain

The overall gain of the chip is a function of the amount of

decimation (N), the settings of the “SHIFT UP” circuit

(SCALE), the GAIN setting, the sum of the F1 coefficients,

and the sum of the F2 coefficients. The overall gain is shown

below in Equation 2.

(2)

Where:

(3)

and:

(4)

It is assumed that the DDC output words are treated as frac-

tional 2’s complement words. The numerators of

and

equal the sums of the impulse response coefficients of

F1 and F2, respectively. For the STD and GSM sets,

and

are nearly equal to unity. Observe that the

term in (2) is cancelled by the DVGA operation so that the

entire gain of the DRCS is independent of the DVGA setting

when EXP_INH=0. The

appearing in (2) is the result of the

6dB conversion loss in the mixer. For full-scale square wave

inputs the

should be set to 1 to prevent signal distortion.

Data Latency and Group Delay

The CLC5903 latency calculation assumes that the FIR filter

latency will be equal to the time required for data to propa-

gate through one half of the taps. The CIC filter provides 4N

equivalent taps where N is the CIC decimation ratio. F1 and

F2 provide 21 and 63 taps respectively. When these filters

are reflected back to the input rate, the effective taps are

increased by decimation. This results in a total of 298N taps

when the F2 decimation is 2 and 550N taps when the F2

decimation is 4.

The latency is then 149N CK periods when the F2 decima-

tion is 2 and 275N CK periods when the F2 decimation is 4.

The CLC5903 filters are linear phase filters so the group

delay remains constant.

Output Modes

After processing by the DDC, the data is then formatted for

output.

All output data is two’s complement. The serial outputs

power up in a tri-state condition and must be enabled

when the chip is configured. Parallel outputs are

enabled by the POUT_EN pin.

Output formats include truncation to 8 or 32 bits, rounding to

16 or 24 bits, and a 12-bit floating point format (4-bit expo-

nent, 8-bit mantissa, 138dB numeric range). This function is

performed in the OUTPUT CIRCUIT shown in Figure 29.

The channel outputs are accessible through serial output

pins and a 16-bit parallel output port. The RDY pin is pro-

vided to notify the user that a new output sample period

(OSP) has begun. OSP refers to the interval between output

samples at the decimated output rate. For example, if the

input rate (and clock rate) is 52 MHz and the overall decima-

tion factor is 192 (N=48, F2 decimation=2) the OSP will be

3.69 microseconds which corresponds to an output sample

Figure 28. CIC, F1, & F2 GSM Passband Flatness

100

−2

−1.5

−1

−0.5

0.5

Combined Frequency Response of CIC/F1/F2 Using GSM Set

Frequency (KHz)

DDC

--- DEC

()

SCALE

–

AGAIN

EXP_INH

–

()

⋅

–

[]

GAIN

⋅

⋅⋅

1 i

()

∑

-----------------------

2 i

()

∑

-----------------------

AGAIN

---

DIVIDE

BOUT

AOUT

RATE

POUT_SEL[2..0]

POUT[15..0]

POUT_EN

SCK

RDY

MUX

RDY_POL, SCK_POL, SFS_POL

Figure 29. CLC5903 output circuit

SFS

SCK_IN

Output Modes (Continued)

CLC5903 датащи(PDF) 17 Page - National Semiconductor (TI)

CLC5903 датащи(HTML) 17 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

датащи скачать

ссылки URL