P89C51RC2BASLASH01 datasheet(2/68 Pages) PHILIPS

2 / 68 page

Philips Semiconductors

Preliminary data

P89C51RA2/RB2/RC2/RD2xx

80C51 8-bit Flash microcontroller family

8KB/16KB/32KB/64KB ISP/IAP Flash with 512B/512B/512B/1KB RAM

2002 Jul 18

DESCRIPTION

The P89C51RA2/RB2/RC2/RD2xx contains a non-volatile

8KB/16KB/32KB/64KB Flash program memory that is both parallel

programmable and serial In-System and In-Application

Programmable. In-System Programming (ISP) allows the user to

download new code while the microcontroller sits in the application.

In-Application Programming (IAP) means that the microcontroller

fetches new program code and reprograms itself while in the

system. This allows for remote programming over a modem link.

A default serial loader (boot loader) program in ROM allows serial

In-System programming of the Flash memory via the UART without

the need for a loader in the Flash code. For In-Application

Programming, the user program erases and reprograms the Flash

memory by use of standard routines contained in ROM.

The device supports 6-clock/12-clock mode selection by

programming a Flash bit using parallel programming or

In-System Programming. In addition, an SFR bit (X2) in the clock

control register (CKCON) also selects between 6-clock/12-clock

mode.

Additionally, when in 6-clock mode, peripherals may use either 6

clocks per machine cycle or 12 clocks per machine cycle. This

choice is available individually for each peripheral and is selected by

bits in the CKCON register.

This device is a Single-Chip 8-Bit Microcontroller manufactured in an

advanced CMOS process and is a derivative of the 80C51

microcontroller family. The instruction set is 100% compatible with

the 80C51 instruction set.

The device also has four 8-bit I/O ports, three 16-bit timer/event

counters, a multi-source, four-priority-level, nested interrupt structure,

an enhanced UART and on-chip oscillator and timing circuits.

The added features of the P89C51RA2/RB2/RC2/RD2xx make it a

powerful microcontroller for applications that require pulse width

modulation, high-speed I/O and up/down counting capabilities such

as motor control.

FEATURES

• 80C51 Central Processing Unit

• On-chip Flash Program Memory with In-System Programming

(ISP) and In-Application Programming (IAP) capability

• Boot ROM contains low level Flash programming routines for

downloading via the UART

• Can be programmed by the end-user application (IAP)

• Parallel programming with 87C51 compatible hardware interface

to programmer

• Supports 6-clock/12-clock mode via parallel programmer (default

clock mode after ChipErase is 12-clock)

• 6-clock/12-clock mode Flash bit erasable and programmable via

ISP

• 6-clock/12-clock mode programmable “on-the-fly” by SFR bit

• Peripherals (PCA, timers, UART) may use either 6-clock or

12-clock mode while the CPU is in 6-clock mode

• Speed up to 20 MHz with 6-clock cycles per machine cycle

(40 MHz equivalent performance); up to 33 MHz with 12 clocks

per machine cycle

• Fully static operation

• RAM expandable externally to 64 kbytes

• Four interrupt priority levels

• Seven interrupt sources

• Four 8-bit I/O ports

• Full-duplex enhanced UART

– Framing error detection

– Automatic address recognition

• Power control modes

– Clock can be stopped and resumed

– Idle mode

– Power down mode

• Programmable clock-out pin

• Second DPTR register

• Asynchronous port reset

• Low EMI (inhibit ALE)

• Programmable Counter Array (PCA)

– PWM

– Capture/compare

P89C51RC2BA/01 датащи(PDF) 2 Page - NXP Semiconductors

P89C51RC2BA/01 датащи(HTML) 2 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

датащи скачать

ссылки URL