CS4216 datasheet(16/58 Pages) CIRRUS

16 / 58 page

externally. In Master sub-mode, the serial port

signal transitions are controlled with respect to

the internal analog sampling clock to minimize

the amount of digital noise coupled into the ana-

log section. Since SSYNC and SCLK are

externally derived in Slave sub-mode, optimum

noise management cannot be obtained; therefore,

Master sub-modes should be used whenever pos-

sible.

Master Sub-Mode (SM3)

Master su b- mod e is selected by sett in g

MF4:MA = 1, which configures SSYNC and

SCLK as outputs from the CS4216. During

power down, SSYNC and SCLK are driven high

impedance, and during reset they both are driven

low. In Master sub-mode the number of bits per

frame determines how many codecs can occupy

the serial bus and is illustrated in Figure 8.

Bits Per Frame (Master Sub-Mode)

MF8:SFS2 selects the number of bits per frame.

The two options are MF8:SFS2 = 1 which se-

lects 128 bits per frame, and MF8:SFS2 = 0

which selects 64 bits per frame.

Selecting 128 bits per frame (MF8:SFS2 = 1) al-

lows two CS4216s to operate from the same

serial bus since each codec requires 64 bit peri-

ods. The sub-frame used by an individual codec

is selected using MF7:SFS1. MF7:SFS1 = 0 se-

lects sub-frame 1 which is the first 64 bits

following the SSYNC pulse. MF7:SFS1 = 1 se-

lects sub-frame 2 which is the last 64 bits of the

frame.

Selecting 64 bits per frame (MF8:SFS2 = 0) al-

lows only one CS4216 to occupy the serial port.

Since there is only one sub-frame (which is

equal to one frame), MF7:SFS1 is defined differ-

ently in this mode. MF7:SFS1 selects the format

of SSYNC. MF7:SFS1 = 0 selects an SSYNC

pulse one SCLK period high, directly preceding

the data as shown in the center portion of Fig-

ure 8. This format is used for all other Master

and Slave sub-modes in SM3. If MF7:SFS1 = 1,

an alternate SSYNC format is chosen in which

SSYNC is high during the entire Word A

(32 bits), which includes the left sample, and

low for the entire Word B (32 bits), which in-

cludes the right sample. This alternate format for

SSYNC is illustrated in the bottom portion of

Figure 8 and is only available in Master sub-

mode with 64 bits per frame. A more detailed

timing diagram for the 64 bits-per-frame Master

sub-mode is shown in Figure 9.

Sample Frequency Selection (Master Sub-Mode)

In SM3, Master sub-mode, the multifunction

pins MF1:F1, MF2:F2, and MF3:F3 are used to

select the sample frequency divider. Table 3 lists

the decoding for the sample frequency select

pins where the sample frequency selected is

CLKIN/N. Also shown are the sample frequen-

cies obtained by using one of two example

ma ster clo ck s : either 12.288 MHz or

11.2896 MHz. The codec must be reset when

changing sample frequencies to allow the codec

to calibrate to the new sample frequency.

Slave Sub-Mode (SM3)

In SM3, Slave sub-mode is selected by setting

MF4:MA = 0 which configures SSYNC and

SCLK as inputs to the CS4216. These two sig-

nals must be externally derived from CLKIN. In

Slave sub-mode, the phase relationship between

SCLK/SSYNC and CLKIN cannot be controlled

since SCLK and SSYNC are externally derived.

Therefore, the noise performance may be slightly

worse than when using the master sub-mode.

The number of sub-frames on the serial port is

selected using MF1:F1 and MF2:F2. In Slave

sub-mode MF3:F3 works as a general purpose

input. Figures 10 through 12 illustrate the Slave

sub-mode formats.

CS4216

DS83F2

CS4216 датащи(PDF) 16 Page - Cirrus Logic

CS4216 датащи(HTML) 16 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

датащи скачать

ссылки URL