AM3703CUS datasheet(212/280 Pages) TI

212 / 280 page

AM3715, AM3703

SPRS616F

– JUNE 2010 – REVISED AUGUST 2011

www.ti.com

6.6

Serial Communications Interfaces

6.6.1

Multichannel Buffered Serial Port (McBSP)

NOTE

For more information, see Multi-Channel Buffered Serial Port chapter of the AM/DM37x

Multimedia Device Technical Reference Manual (literature number SPRUGN4).

The Multichannel Buffered Serial Port (McBSP) provides a full duplex direct serial interface between the

chip and other devices in a system such as other application chips, codecs. It can accommodate a wide

range of peripherals and clocked frame oriented protocols (I2S, PCM, T ) due to its high level of versatility.

McBSP may support two types of data transfer at the system level:

•

The full cycle mode, for which one clock period is used to transfer the data, generated on one edge

and captured on the same edge (one clock period later).

•

The half cycle mode, for which one half clock period is used to transfer the data, generated on one

edge and captured on the opposite edge (one half clock period later). Note that a new data is

generated only every clock period, which secures the required hold time.

The interface clock (clkx/clkr) activation edge (data/frame sync capture and generation) has to be

configured accordingly with the external peripheral (activation edge capability) and the type of data

transfer required at the system level.

Depending on the number of pins, McBSP supports either:

•

6-pin mode: dx and dr as data pins; clkx, clkr, fsx, and fsr as control pins

•

4-pin mode: dx and dr as data pins; clkx and fsx pins as control pins. The clkx and fsx pins are

internally looped back, via software configuration, respectively to the clkr and fsr internal signals for

data receive.

McBSP1 supports the 6-pin mode. McBSP2, 3, 4, and 5 support only the 4-pin mode.

The following sections describe the timing characteristics for applications in normal mode (that is, McBSPx

connected to one peripheral) and T applications in multipoint mode.

6.6.1.1

McBSP Timing Conditions

—Normal Mode

Table 6-46 through Table 6-70 assume testing over the recommended operating conditions and electrical

characteristic conditions below (see Figure 6-36 through Figure 6-43).

Table 6-45. McBSP Timing Conditions

—Normal Mode

TIMING CONDITION PARAMETER

VALUE

UNIT

Input Conditions

Input signal rise time

Input signal fall time

Output Condition

CLOAD

Output load capacitance(1)

(1) Buffer strength configuration:

–

McBSP4 - Set #1: LB0 = 1.

–

Otherwise: LB0 = 0.

212

Timing Requirements and Switching Characteristics

Submit Documentation Feedback

Product Folder Link(s): AM3715 AM3703

AM3703CUS датащи(PDF) 212 Page - Texas Instruments

AM3703CUS датащи(HTML) 212 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL