AM3703CUS datasheet(80/280 Pages) TI

80 / 280 page

AM3715, AM3703

SPRS616F

– JUNE 2010 – REVISED AUGUST 2011

www.ti.com

Table 2-3. Ball Characteristics (CUS Pkg.)(1) (continued)

BALL

PIN NAME [2]

MODE [3]

TYPE [4]

BALL RESET BALL RESET RESET REL. POWER [8]

HYS [9]

BUFFER

PULLUP

IO CELL [12]

NUMBER [1]

STATE [5]

REL. STATE MODE [7]

STRENGTH

/DOWN

[6]

(mA) [10]

TYPE [11]

N21

cap_vdd_bb_mpu_iv 0

PWR

N20

cap_vddu_array

PWR

AB15

vssa_dac

GND

AB13

vdda_dac

PWR

H11, H14,

vss

GND

H16, J11,

J12, J13, J14,

J15, J16,

K10, K11,

K14, K15, L8,

L10, L13,

L17, M9,

M10, M11,

M13, M16,

N9, N10,

N11, N12,

N13, N14,

N15, N16,

P8, P10, P11,

P12, P13,

P14, P15,

P17, R10,

R11, R14,

R15, T9, T10,

T11, T12,

T13, T14,

T15, T16, U9,

U11, U14,

U15, U16,

V15, V16

AD1, A1, A2, No Connect

(2)

W15

sys_xtalgnd

GND

(1) NA in this table stands for "Not Applicable".

(2) Pins labeled as "No connect" must be left unconnected. Any connections to these pins may result in unpredictable behavior.

(3) Depending on the sys_clkreq direction the corresponding reset released state value can be:

–

Z if sys_clkreq is used as input

–

1 if sys_clkreq is used as output

For a full description of the sys_clkreq control, see Power, Reset, and Clock Management chapter of the AM/DM37x Multimedia Device

Technical Reference Manual (literature number SPRUGN4).

(4) PU = [50 to 100 k

Ω] per default or [10 to 50 kΩ] according to the selected mode. For a full description of the pull-up drive strength

programming, see the PRG_SDMMC_PUSTRENGTH configuration register bit field in the System Control Module chapter of the

AM/DM37x Multimedia Device Technical Reference Manual (literature number SPRUGN4). PD: 30 to 150 k

Ω.

(5) The usage of this GPIO is strongly restricted. For more information, see the General-Purpose Interface chapter of the AM/DM37x

Multimedia Device Technical Reference Manual (literature number SPRUGN4).

(6) The drive strength is fixed regardless of the load. The driver is designed to drive 75

Ω for video applications.

(7) In buffer mode, the drive strength is fixed regardless of the load. The driver is designed to drive 75

Ω for video applications. In bypass

mode, the drive strength is 0.47 mA.

(8) The drive strength of these IOs is set according to the programmable load range: 2 pF to 4 pF per default or 4 pF to 12 pF. For a full

description of the drive strength programming, see the System Control Module chapter of the AM/DM37x Multimedia Device Technical

Reference Manual (literature number SPRUGN4).

(9) In the safe_mode_out1, the buffer is configured to drive 1.

(10) The pullup and pulldown can be either the standard LVCMOS 100-

μA drive strength or the I2C pullup and pulldown described below:

Nominal resistance = 1.66 k

Ω in high-speed mode with a load range of 5 pF to 12 pF, 4.5 kΩ in standard / fast mode with a load range

of 5 pF to 15 pF.

(11) The default buffer configuration is High-Speed I2C point-to-point mode using internal pullup. For a full description of the pull drive

strength programming, see prg_i2c1_pullupresx, prg_i2c1_lb1lb0, and prg_sr_pullupresx, prg_sr_lb bits of the CONTROL_PROG_IO1,

CONTROL_PROG_IO_WKUP1 control modules in the System Control Module / SCM Programming Model / Feature Settings section

and the System Control Module chapter of the AM/DM37x Multimedia Device Technical Reference Manual (literature number

SPRUGN4) to modify the IO settings if required by the targeted interface application.

(12) The default buffer configuration is standard LVCMOS mode (non-I2C). For a full description of the pull drive strength programming, see

PADCONFS bits of CONTROL_PADCONF_X control modules (standard LVCMOS mode), or prg_i2c2_pullupresx, prg_i2c2_lb1lb0, and

prg_i2c3_pullupresx, prg_i2c3_lb1lb0 bits of the CONTROL_PROG_IO2, CONTROL_PROG_IO3 control modules (I2C mode) in the

System Control Module chapter of the AM/DM37x Multimedia Device Technical Reference Manual (literature number SPRUGN4) to

modify the IO settings if required by the targeted interface application.

(13) Mux0 if sys_boot6 is pulled down (clock master).

TERMINAL DESCRIPTION

Submit Documentation Feedback

Product Folder Link(s): AM3715 AM3703

AM3703CUS датащи(PDF) 80 Page - Texas Instruments

AM3703CUS датащи(HTML) 80 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL