7

ELECTRICAL SPECIFICATIONS

OUTPUT

MIN

TYP

MAX

UNITS

NOTES

Output Current

10 or 15

A

10 A for TC10, 15 A for TC15

Short Term Stability, 1 hour, Off Ambient 1, 2

0.0002

0.0006

ºC

25°C ambient

Short Term Stability, 1 hour, On Ambient 1, 2

0.0003

0.0009

ºC

25°C ambient

Long Term Stability, 24 hour, Off Ambient 1, 2

0.00067

0.002

ºC

25°C ambient

Temperature Coefficient

5

10

18

ppm / °C

Compliance Voltage Range

0-15 or 0-20

V

≤15 V for TC10. ≤20 V for TC15.

SENSOR COMPATIBILITY

VALUE

NOTES

NTC Thermistor Sensor Range Voltage

0 - 10 V

NTC Thermistor Bias Current Range

10 µA - 10 mA

Auto-ranging bias current3

2,3,4 Wire RTD Sensor Range

100 Ω - 1 kΩ

Linear Voltage or Current Sensors

Supported

Comparable to LM335 and AD590

Bias Current Accuracy

0.004%

Bias Current Temperature Coefficient

10 ppm/ºC

POWER SUPPLY REQUIREMENTS

VALUE

NOTES

AC Power Supply and Line Frequency

100-240 VAC (± 10%),

3 A, 50-60 Hz

Fuse for 100-240 V

3.15 A 250 AC Fast Blow

(3.15 AH 250 V 5×20 mm)

Replacement fuse:

Littelfuse 02163.15 HXP

Max AC Line Power

200 W

FEEDBACK LOOP: Proportional / Integral / Derivative (PID)

GENERAL SPECIFICATIONS

VALUE

NOTES

Warm-up Time

1 Hour

Remote Interface

USB, Ethernet

Warranty

One (1) Year

Safety Tested To

IEC 61000-3-2

IEC 61000-4-5

IEC 61000-3-3

IEC 61000-4-6

IEC 61000-4-2

IEC 61000-4-8

IEC 61000-4-3

IEC 61010-1

IEC 61000-4-4

EN61010-2-30

European Council Directive 2004/108/EC &

European Council Directive 2006/95/EC

ABSOLUTE MAXIMUM RATINGS

VALUE

UNIT

NOTES

Case Operating Temperature Range

0 to 40

°C

Weight

7.4 (3.36)

lbs (kg)

Size

3.47 × 8.86 × 17.72

(89 × 226 × 450)

inches

(mm)

Case Storage Temperature

-40 to 70

ºC

Humidity

80

%

Relative humidity at 30ºC, non-condensing

1

This specification assumes a steady-state operation with a tuned system using a 10 kΩ thermistor. Minimum Stability achieved by measuring 1 standard

deviation (1σ) away from the mean. Typical Stability achieved by measuring 3 standard deviations (3σ) away from the mean. For more detail, see

TN-TC02. Stability typical for a 14 pin butterfly package laser diode with a 10 kΩ thermistor.

Stability will vary with different load types, thermal designs, and sensors. RTDs and linear voltage and current sensors are much

less sensitive than thermistors to temperature change, so stability results will not match these specifications. See TN-TC01 for

maximizing system performance.

2

When using resistive heaters, stability can only be consistently achieved when setpoint temperatures are 10ºC or more over ambient.

3

A fixed, non-volatile bias current can be configured with a custom sensor using remote command CONST:THERM with Firmware Versions 1.99 and 2.01

and later. See the LAB Series Command Set User Guide for more details.