| поискавой системы для электроныых деталей |
|
WM8803CDT/V датащи(PDF) 29 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8803CDT/V датащи(HTML) 29 Page - Wolfson Microelectronics plc |
|
29 / 45 page ![]() Product Preview WM8803 w PP Rev 1.1 September 2003 29 CCB ADDRESSES The address locations in Table 15 are those used to set the parameters, write data values and to read data values from the WM8803 over the micro-controller interface. The micro-controller interface data format conforms to that of the Sanyo-developed CCB serial bus format. However, a three state circuit is adopted for the data output instead of the open drain circuit used in CCB. Data is input or output after input of the CCB address. See the I/O timing chart for details on the data input and output timing. REGISTER CONTENT R/W CCB ADDRESS B0 B1 B2 B3 A0 A1 A2 A3 Function settings data 1 Write 0xE8 0 0 0 1 0 1 1 1 Function settings data 2 Write 0xE9 1 0 0 1 0 1 1 1 Function settings data 3 Write 0xEA 0 1 0 1 0 1 1 1 Interrupt data output Read 0xEB 1 1 0 1 0 1 1 1 Fs value, CS data output Read 0xEC 0 0 1 1 0 1 1 1 Sub-code Q data output Read 0xED 1 0 1 1 0 1 1 1 Table 15 Register I/O Content and CCB Addresses DATA WRITE PROCEDURE The data input bit length is 16 bits. After inputting data to one of the CCB addresses 0xE8 to 0xEA, set CE to the high level. Input data is acquired on the rising edge of CL. The bits marked “0” in the table are reserved bits. A value of 0 must be written to these bits. DATA READ PROCEDURE Read data is output from DO and goes to the high-impedance state when CE is low. Output starts on the CE rising edge following the establishment of the output address by the CCB command on the DI pin. After operation the DO pin is returned to the high-impedance state by setting CE low. The number of data bits read out differs with the type of data read. Interrupt data has 8bits, the channel status related data (0xEC) has 56bits, and the sub-code Q data (0xED) has 88bits. However, it is not necessary to read out all the data. During readout it is possible to read data up to the point when the CL clock is stopped and the CE pin is set low. For example, when reading the sub-code Q data, if the CRC flags are read and the data is seen to be corrupted, there is no need to read the data following. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |