| поискавой системы для электроныых деталей |
|
UCS1002-2 датащи(PDF) 32 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UCS1002-2 датащи(HTML) 32 Page - Microchip Technology |
|
32 / 114 page ![]() Programmable USB Port Power Controller with Charger Emulation Datasheet Revision 1.4 (07-16-13) 32 SMSC UCS1002 DATASHEET 4.2.4.1 Block Write The Block Write is used to write multiple data bytes to a group of contiguous registers as shown in Table 4.8. APPLICATION NOTE: When using the Block Write protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. 4.2.4.2 Block Read The Block Read is used to read multiple data bytes from a group of contiguous registers as shown in Table 4.9. APPLICATION NOTE: When using the Block Read protocol, the internal address pointer will be automatically incremented after every data byte is received. It will wrap from FFh to 00h. 4.3 Stand-alone Operating Mode Stand-alone mode allows the UCS1002 to operate without active SMBus / I2C communications. Stand- alone mode can be enabled by connecting a pull-down resistor greater or equal to 47 k Ω on the COMM_SEL / ILIM pin as shown in Table 4.1, "UCS1002 Communication Mode and ILIM Selection". When the device is configured to operate in Stand-alone mode, the fault handling and Attach Detection controls are determined via the LATCH and S0 pins as shown in Table 4.10. APPLICATION NOTE: If it is necessary to connect the S0 or LATCH pins to VDD via a pull-up resistor, the pull-up resistor value should be 100 k Ω in order to guarantee VIH specification. Likewise, if it is necessary to connect the S0 or LATCH pins to GND via a pull-down resistor, the pull-down resistor value should be 100 k Ω in order to guarantee VIL specification. Table 4.8 Block Write Protocol START CLIENT ADDRESS WR ACK REGISTER ADDRESS ACK REGISTER DATA ACK 1 ->0 YYYY_YYY 0 0 XXh 0 XXh 0 REGISTER DATA ACK REGISTER DATA ACK . . . REGISTER DATA ACK STOP XXh 0 XXh 0 . . . XXh 0 0 -> 1 Table 4.9 Block Read Protocol START CLIENT ADDRESS WR ACK REGISTER ADDRESS ACK START CLIENT ADDRESS RD ACK REGISTER DATA 1->0 YYYY_YYY 00 XXh 0 1 ->0 YYYY_YYY 1 0 XXh ACK REGISTER DATA ACK REGISTER DATA ACK REGISTER DATA ACK . . . REGISTER DATA NACK STOP 0 XXh 0 XXh 0 XXh 0 . . . XXh 1 0 -> 1 |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |