| поискавой системы для электроныых деталей |
|
STM32L081CB датащи(PDF) 84 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32L081CB датащи(HTML) 84 Page - STMicroelectronics |
|
84 / 110 page ![]() Electrical characteristics STM32L081xx 84/110 DocID027513 Rev 4 Table 58. RAIN max for fADC = 16 MHz(1) Ts (cycles) tS (µs) RAIN max for fast channels (k ) RAIN max for standard channels (k) VDD > 2.7 V VDD > 2.4 V VDD > 2.0 V VDD > 1.8 V VDD > 1.75 V VDD > 1.65 V and TA > 10 °C VDD > 1.65 V and TA > 25 °C 1.5 0.09 0.5 < 0.1 NA NA NA NA NA NA 3.5 0.22 1 0.2 < 0.1 NA NA NA NA NA 7.5 0.47 2.5 1.7 1.5 < 0.1 NA NA NA NA 12.5 0.78 4 3.2 3 1 NA NA NA NA 19.5 1.22 6.5 5.7 5.5 3.5 NA NA NA < 0.1 39.5 2.47 13 12.2 12 10 NA NA NA 5 79.5 4.97 27 26.2 26 24 < 0.1 NA NA 19 160.5 10.03 50 49.2 49 47 32 < 0.1 < 0.1 42 1. Guaranteed by design. Table 59. ADC accuracy(1)(2)(3) Symbol Parameter Conditions Min Typ Max Unit ET Total unadjusted error 1.65 V < VDDA < 3.6 V, range 1/2/3 -2 4 LSB EO Offset error - 1 2.5 EG Gain error - 1 2 EL Integral linearity error - 1.5 2.5 ED Differential linearity error - 1 1.5 ENOB Effective number of bits 10.2 11 bits Effective number of bits (16-bit mode oversampling with ratio =256)(4) 11.3 12.1 - SINAD Signal-to-noise distortion 63 69 - dB SNR Signal-to-noise ratio 63 69 - Signal-to-noise ratio (16-bit mode oversampling with ratio =256)(4) 70 76 - THD Total harmonic distortion - -85 -73 1. ADC DC accuracy values are measured after internal calibration. 2. ADC Accuracy vs. Negative Injection Current: Injecting negative current on any of the standard (non-robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins which may potentially inject negative current. Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in Section 6.3.12 does not affect the ADC accuracy. 3. Better performance may be achieved in restricted VDDA, frequency and temperature ranges. 4. This number is obtained by the test board without additional noise, resulting in non-optimized value for oversampling mode. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |