DM9302 datasheet(53/64 Pages) DAVICOM

53 / 64 page

DM9302

10/100Mbps Ethernet Fiber/Twisted Pair Media Converter with Local bus

Preliminary datasheet

DM9302-15-DS-P01

July 30, 2009

9.3 Internal PHY functions

9.3.1 100Base-TX Operation

The transmitter section contains the following

functional blocks:

- 4B5B Encoder

- Scrambler

- Parallel to Serial Converter

- NRZ to NRZI Converter

- NRZI to MLT-3

- MLT-3 Driver

9.3.1.1 4B5B Encoder

The 4B5B encoder converts 4-bit (4B) nibble data

generated by the MAC Reconciliation Layer into a

5-bit (5B) code group for transmission, see reference

Table 1. This conversion is required for control and

packet data to be combined in code groups. The

4B5B encoder substitutes the first 8 bits of the MAC

preamble with a J/K code-group pair (11000 10001)

upon transmit. The 4B5B encoder continues to

replace subsequent 4B preamble and data nibbles

with corresponding 5B code-groups. At the end of the

transmit packet, upon the deassertion of the Transmit

Enable signal from the MAC Reconciliation layer, the

4B5B encoder injects the T/R code-group pair (01101

00111) indicating the end of frame. After the T/R

code-group pair, the 4B5B encoder continuously

injects IDLEs into the transmit data stream until

Transmit Enable is asserted and the next transmit

packet is detected.

9.3.1.2 Scrambler

The scrambler is required to control the radiated

emissions (EMI) by spreading the transmit energy

across the frequency spectrum at the media

connector and on the twisted pair cable in

100Base-TX operation.

By scrambling the data, the total energy presented to

the cable is randomly distributed over a wide

frequency range. Without the scrambler, energy

levels on the cable could peak beyond FCC

limitations at frequencies related to the repeated 5B

sequences, like the continuous transmission of IDLE

symbols. The scrambler output is combined with the

NRZ 5B data from the code-group encoder via an

XOR logic function. The result is a scrambled data

stream with sufficient randomization to decrease

radiated emissions at critical frequencies.

9.3.1.3 Parallel to Serial Converter

The Parallel to Serial Converter receives parallel 5B

scrambled data from the scrambler, and serializes it

(converts it from a parallel to a serial data stream).

The serialized data stream is then presented to the

NRZ to NRZI encoder block

9.3.1.4 NRZ to NRZI Encoder

After the transmit data stream has been scrambled

and serialized, the data must be NRZI encoded for

compatibility with the TP-PMD standard, for 100Base

-TX transmission over Category-5 unshielded twisted

pair cable.

9.3.1.5 MLT-3 Converter

The MLT-3 conversion is accomplished by converting

the data stream output, from the NRZI encoder into

two binary data streams, with alternately phased logic

one event.

9.3.1.6 MLT-3 Driver

The two binary data streams created at the MLT-3

converter are fed to the twisted pair output driver,

which converts these streams to current sources and

alternately drives either side of the transmit

transformer’s primary winding, resulting in a minimal

current MLT-3 signal.

DM9302 датащи(PDF) 53 Page - Davicom Semiconductor, Inc.

DM9302 датащи(HTML) 53 Page - Davicom Semiconductor, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

датащи скачать

ссылки URL