ATmega328P datasheet(212/448 Pages) ATMEL

212 / 448 page

212

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

• Bit 6 - TXCIEn: TX Complete Interrupt Enable

Writing this bit to one enables interrupt on the TXCn Flag. A USART Transmit Complete interrupt

will be generated only if the TXCIEn bit is written to one, the Global Interrupt Flag in SREG is

written to one and the TXCn bit in UCSRnA is set.

• Bit 5 - UDRIE: USART Data Register Empty Interrupt Enable

Writing this bit to one enables interrupt on the UDREn Flag. A Data Register Empty interrupt will

be generated only if the UDRIE bit is written to one, the Global Interrupt Flag in SREG is written

to one and the UDREn bit in UCSRnA is set.

• Bit 4 - RXENn: Receiver Enable

Writing this bit to one enables the USART Receiver in MSPIM mode. The Receiver will override

normal port operation for the RxDn pin when enabled. Disabling the Receiver will flush the

receive buffer. Only enabling the receiver in MSPI mode (i.e. setting RXENn=1 and TXENn=0)

has no meaning since it is the transmitter that controls the transfer clock and since only master

mode is supported.

• Bit 3 - TXENn: Transmitter Enable

Writing this bit to one enables the USART Transmitter. The Transmitter will override normal port

operation for the TxDn pin when enabled. The disabling of the Transmitter (writing TXENn to

zero) will not become effective until ongoing and pending transmissions are completed, i.e.,

when the Transmit Shift Register and Transmit Buffer Register do not contain data to be trans-

mitted. When disabled, the Transmitter will no longer override the TxDn port.

• Bit 2:0 - Reserved Bits in MSPI mode

When in MSPI mode, these bits are reserved for future use. For compatibility with future devices,

these bits must be written to zero when UCSRnB is written.

20.8.4

UCSRnC – USART MSPIM Control and Status Register n C

• Bit 7:6 - UMSELn1:0: USART Mode Select

These bits select the mode of operation of the USART as shown in Table 20-4. See ”UCSRnC –

USART Control and Status Register n C” on page 197 for full description of the normal USART

operation. The MSPIM is enabled when both UMSELn bits are set to one. The UDORDn,

UCPHAn, and UCPOLn can be set in the same write operation where the MSPIM is enabled.

Bit

UMSELn1

UMSELn0

UDORDn

UCPHAn

UCPOLn

UCSRnC

Read/Write

R/W

Initial Value

Table 20-4.

UMSELn Bits Settings

UMSELn1

UMSELn0

Mode

Asynchronous USART

Synchronous USART

Reserved

Master SPI (MSPIM)

ATmega328P датащи(PDF) 212 Page - ATMEL Corporation

ATmega328P датащи(HTML) 212 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL