ATmega328P datasheet(98/448 Pages) ATMEL

98 / 448 page

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

The OCR0x Register access may seem complex, but this is not case. When the double buffering

is enabled, the CPU has access to the OCR0x Buffer Register, and if double buffering is dis-

abled the CPU will access the OCR0x directly.

14.5.1

Force Output Compare

In non-PWM waveform generation modes, the match output of the comparator can be forced by

writing a one to the Force Output Compare (FOC0x) bit. Forcing compare match will not set the

OCF0x Flag or reload/clear the timer, but the OC0x pin will be updated as if a real compare

match had occurred (the COM0x1:0 bits settings define whether the OC0x pin is set, cleared or

toggled).

14.5.2

Compare Match Blocking by TCNT0 Write

All CPU write operations to the TCNT0 Register will block any compare match that occur in the

next timer clock cycle, even when the timer is stopped. This feature allows OCR0x to be initial-

ized to the same value as TCNT0 without triggering an interrupt when the Timer/Counter clock is

enabled.

14.5.3

Using the Output Compare Unit

Since writing TCNT0 in any mode of operation will block all compare matches for one timer clock

cycle, there are risks involved when changing TCNT0 when using the Output Compare Unit,

independently of whether the Timer/Counter is running or not. If the value written to TCNT0

equals the OCR0x value, the compare match will be missed, resulting in incorrect waveform

generation. Similarly, do not write the TCNT0 value equal to BOTTOM when the counter is

downcounting.

The setup of the OC0x should be performed before setting the Data Direction Register for the

port pin to output. The easiest way of setting the OC0x value is to use the Force Output Com-

pare (FOC0x) strobe bits in Normal mode. The OC0x Registers keep their values even when

changing between Waveform Generation modes.

Be aware that the COM0x1:0 bits are not double buffered together with the compare value.

Changing the COM0x1:0 bits will take effect immediately.

14.6

Compare Match Output Unit

The Compare Output mode (COM0x1:0) bits have two functions. The Waveform Generator uses

the COM0x1:0 bits for defining the Output Compare (OC0x) state at the next compare match.

Also, the COM0x1:0 bits control the OC0x pin output source. Figure 14-4 shows a simplified

schematic of the logic affected by the COM0x1:0 bit setting. The I/O Registers, I/O bits, and I/O

pins in the figure are shown in bold. Only the parts of the general I/O port control registers (DDR

and PORT) that are affected by the COM0x1:0 bits are shown. When referring to the OC0x

state, the reference is for the internal OC0x Register, not the OC0x pin. If a system reset occur,

the OC0x Register is reset to “0”.

ATmega328P датащи(PDF) 98 Page - ATMEL Corporation

ATmega328P датащи(HTML) 98 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL