ATmega328P datasheet(211/448 Pages) ATMEL

211 / 448 page

211

8161D–AVR–10/09

ATmega48PA/88PA/168PA/328P

20.8

The following section describes the registers used for SPI operation using the USART.

20.8.1

UDRn – USART MSPIM I/O Data Register

The function and bit description of the USART data register (UDRn) in MSPI mode is identical to

normal USART operation. See “UDRn – USART I/O Data Register n” on page 195.

20.8.2

UCSRnA – USART MSPIM Control and Status Register n A

• Bit 7 - RXCn: USART Receive Complete

This flag bit is set when there are unread data in the receive buffer and cleared when the receive

buffer is empty (i.e., does not contain any unread data). If the Receiver is disabled, the receive

buffer will be flushed and consequently the RXCn bit will become zero. The RXCn Flag can be

used to generate a Receive Complete interrupt (see description of the RXCIEn bit).

• Bit 6 - TXCn: USART Transmit Complete

This flag bit is set when the entire frame in the Transmit Shift Register has been shifted out and

there are no new data currently present in the transmit buffer (UDRn). The TXCn Flag bit is auto-

matically cleared when a transmit complete interrupt is executed, or it can be cleared by writing

a one to its bit location. The TXCn Flag can generate a Transmit Complete interrupt (see

description of the TXCIEn bit).

• Bit 5 - UDREn: USART Data Register Empty

The UDREn Flag indicates if the transmit buffer (UDRn) is ready to receive new data. If UDREn

is one, the buffer is empty, and therefore ready to be written. The UDREn Flag can generate a

Data Register Empty interrupt (see description of the UDRIE bit). UDREn is set after a reset to

indicate that the Transmitter is ready.

• Bit 4:0 - Reserved Bits in MSPI mode

When in MSPI mode, these bits are reserved for future use. For compatibility with future devices,

these bits must be written to zero when UCSRnA is written.

20.8.3

UCSRnB – USART MSPIM Control and Status Register n B

• Bit 7 - RXCIEn: RX Complete Interrupt Enable

Writing this bit to one enables interrupt on the RXCn Flag. A USART Receive Complete interrupt

will be generated only if the RXCIEn bit is written to one, the Global Interrupt Flag in SREG is

written to one and the RXCn bit in UCSRnA is set.

Bit

RXCn

TXCn

UDREn

UCSRnA

Read/Write

R/W

Initial Value

Bit

RXCIEn

TXCIEn

UDRIE

RXENn

TXENn

UCSRnB

Read/Write

R/W

Initial Value

ATmega328P датащи(PDF) 211 Page - ATMEL Corporation

ATmega328P датащи(HTML) 211 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL