ATmega16A datasheet(78/352 Pages) ATMEL

78 / 352 page

8154B–AVR–07/09

ATmega16A

inverted PWM outputs. The small horizontal line marks on the TCNT0 slopes represent compare

matches between OCR0 and TCNT0.

Figure 14-6. Fast PWM Mode, Timing Diagram

The Timer/Counter Overflow Flag (TOV0) is set each time the counter reaches MAX. If the inter-

rupt is enabled, the interrupt handler routine can be used for updating the compare value.

In fast PWM mode, the compare unit allows generation of PWM waveforms on the OC0 pin. Set-

ting the COM01:0 bits to 2 will produce a non-inverted PWM and an inverted PWM output can

be generated by setting the COM01:0 to 3 (See Table 14-4 on page 83). The actual OC0 value

will only be visible on the port pin if the data direction for the port pin is set as output. The PWM

waveform is generated by setting (or clearing) the OC0 Register at the compare match between

OCR0 and TCNT0, and clearing (or setting) the OC0 Register at the timer clock cycle the coun-

ter is cleared (changes from MAX to BOTTOM).

The PWM frequency for the output can be calculated by the following equation:

The N variable represents the prescale factor (1, 8, 64, 256, or 1024).

The extreme values for the OCR0 Register represents special cases when generating a PWM

waveform output in the fast PWM mode. If the OCR0 is set equal to BOTTOM, the output will be

a narrow spike for each MAX+1 timer clock cycle. Setting the OCR0 equal to MAX will result in a

constantly high or low output (depending on the polarity of the output set by the COM01:0 bits.)

A frequency (with 50% duty cycle) waveform output in fast PWM mode can be achieved by set-

ting OC0 to toggle its logical level on each compare match (COM01:0 = 1). The waveform

generated will have a maximum frequency of f

OC0 = fclk_I/O/2 when OCR0 is set to zero. This fea-

ture is similar to the OC0 toggle in CTC mode, except the double buffer feature of the output

compare unit is enabled in the fast PWM mode.

14.7.4

Phase Correct PWM Mode

The phase correct PWM mode (WGM01:0 = 1) provides a high resolution phase correct PWM

waveform generation option. The phase correct PWM mode is based on a dual-slope operation.

The counter counts repeatedly from BOTTOM to MAX and then from MAX to BOTTOM. In non-

TCNTn

OCRn Update and

TOVn Interrupt Flag Set

Period

OCn

(COMn1:0 = 2)

(COMn1:0 = 3)

OCRn Interrupt Flag Set

fOCnPWM

clk_I/O

N 256

⋅

------------------

ATmega16A датащи(PDF) 78 Page - ATMEL Corporation

ATmega16A датащи(HTML) 78 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL