STM32W108HB datasheet(49/179 Pages) STMICROELECTRONICS

49 / 179 page

STM32W108CB, STM32W108HB

General-purpose input/outputs

Doc ID 16252 Rev 2

49/179

6.1.4

Reset

A full chip reset is one due to power on (low or high voltage), the NRST pin, the watchdog, or

the SYSRESETREQ bit. A full chip reset affects the GPIO configuration as follows:

●

The GPIO_PxCFGH/L configurations of all pins are configured as floating inputs.

●

The GPIO_EXTREGEN bit is set in the GPIO_DBGCFG register, which overrides the

normal configuration for PA7.

●

The GPIO_DEBUGDIS bit in the GPIO_DBGCFG register is cleared, allowing Serial

Wire/JTAG access to override the normal configuration of PC0, PC2, PC3, and PC4.

6.1.5

nBOOTMODE

nBOOTMODE is a special alternate function of PA5 that is active only during a pin reset

(NRST) or a power-on-reset of the always-powered domain (POR_HV). If nBOOTMODE is

asserted (pulled or driven low) when coming out of reset, the processor starts executing an

embedded serial boot loader instead of its normal program.

While in reset and during the subsequent power-on-reset startup delay (512 high-frequency

RC oscillator periods), PA5 is automatically configured as an input with a pull-up resistor. At

the end of this time, the STM32W108 samples nBOOTMODE: a high level selects normal

startup, and a low level selects the boot loader. After nBOOTMODE has been sampled, PA5

is configured as a floating input. The GPIO_BOOTMODE bit in the GPIO_DBGSTAT register

captures the state of nBOOTMODE so that software may act on this signal if required.

Note:

To avoid inadvertently asserting nBOOTMODE, PA5's capacitive load should not exceed

252 pF.

6.1.6

GPIO modes

Analog mode

Analog mode enables analog functions, and disconnects a pin from the digital input and

output logic. Only the following GPIO pins have analog functions:

●

PA4, PA5, PB5, PB6, PB7, and PC1 can be analog inputs to the ADC.

●

PB0 can be an external analog voltage reference input to the ADC, or it can output the

internal analog voltage reference from the ADC.

●

PC6 and PC7 can connect to an optional 32.768 kHz crystal.

Note:

When an external timing source is required, a 32.768 kHz crystal is commonly connected to

PC6 and PC7. Alternatively, when PC7 is configured as a digital input, PC7 can accept a

digital external clock input.

When configured in analog mode:

●

The output drivers are disabled.

●

The internal pull-up and pull-down resistors are disabled.

●

The Schmitt trigger input is connected to a high logic level.

●

Reading GPIO_PxIN returns a constant 1.

STM32W108HB датащи(PDF) 49 Page - STMicroelectronics

STM32W108HB датащи(HTML) 49 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL