 |
поискавой системы для электроныых деталей |
|
|
поискавой системы для электроныых деталей |
|
STM32W108HB датащи(PDF) 71 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32W108HB датащи(HTML) 71 Page - STMicroelectronics |
|
|
71 / 179 page  STM32W108CB, STM32W108HB Serial interfaces Doc ID 16252 Rev 2 71/179 7.6.2 UART configuration register (SC1_UARTCFG) Address offset: 0xC85C Reset value: 0x0000 0000 [2] SC_UARTTXFREE: This bit is set when the transmit FIFO has space for at least one byte. [1] SC_UARTRXVAL: This bit is set when the receive FIFO contains at least one byte. [0] SC_UARTCTS: This bit is set when both the transmit FIFO and the transmit serializer are empty. 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 rw rw rw rw rw rw rw rw rw rw rw rw rw rw rw rw 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 SC_UA RTAUT O SC_UA RTFLO W SC_U ARTO DD SC_UA RTPAR SC_UA RT2ST P SC_UA RT8BI T SC_UA RTRTS rw rw rw rw rw rw rw rw rw rw rw rw rw rw rw rw [6] SC_UARTAUTO: Set this bit to enable automatic nRTS control by hardware (SC_UARTFLOW must also be set). When automatic control is enabled, nRTS will be deasserted when the receive FIFO has space for only one more byte (inhibits transmission from the other device) and will be asserted if it has space for more than one byte (enables transmission from the other device). The SC_UARTRTS bit in this register has no effect if this bit is set. [5] SC_UARTFLOW: Set this bit to enable using nRTS/nCTS flow control signals. Clear this bit to disable the signals. When this bit is clear, the UART transmitter will not be inhibited by nCTS. [4] SC_UARTODD: If parity is enabled, specifies the kind of parity. 0: Even parity.1: Odd parity. [3] SC_UARTPAR: Specifies whether to use parity bits. 0: Don't use parity.1: Use parity. [2] SC_UART2STP: Number of stop bits transmitted. 0: 1 stop bit.1: 2 stop bits. [1] SC_UART8BIT: Number of data bits. 0: 7 data bits.1: 8 data bits. [0] SC_UARTRTS: nRTS is an output to control the flow of serial data sent to the STM32W108 from another device. This bit directly controls the output at the nRTS pin (SC_UARTFLOW must be set and SC_UARTAUTO must be cleared). When this bit is set, nRTS is asserted (pin is low, 'XON', RS232 positive voltage); the other device's transmission is enabled. When this bit is cleared, nRTS is deasserted (pin is high, 'XOFF', RS232 negative voltage), the other device's transmission is inhibited. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Russian ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
