OMAP3530-HiRel datasheet(12/239 Pages) TI

12 / 239 page

2.2 Ball Characteristics

OMAP3525-HiRel and OMAP3530-HiRel Applications Processors

SPRS599 – JUNE 2009

www.ti.com

Table 2-1 and Table 2-2 describe the terminal characteristics and the signals multiplexed on each pin for

the CBB and CBC packages, respectively. The following list describes the table column headers.

1. BALL BOTTOM: Ball number(s) on the bottom side associated with each signal(s) on the bottom.

2. BALL TOP: Ball number(s) on the top side associated with each signal(s) on the top.

3. PIN NAME: Names of signals multiplexed on each ball (also notice that the name of the pin is the

signal name in mode 0).

Note: Table 2-1 and Table 2-2 do not take into account subsystem pin multiplexing options.

Subsystem pin multiplexing options are described in Section 2.4, Signal Descriptions.

4. MODE: Multiplexing mode number.

Mode 0 is the primary mode; this means that when mode 0 is set, the function mapped on the pin

corresponds to the name of the pin. There is always a function mapped on the primary mode.

Notice that primary mode is not necessarily the default mode.

Note: The default mode is the mode which is automatically configured on release of the internal

GLOBAL_PWRON reset; also see the RESET REL. MODE column.

Modes 1 to 7 are possible modes for alternate functions. On each pin, some modes are effectively

used for alternate functions, while some modes are not used and do not correspond to a functional

configuration.

5. TYPE: Signal direction

–

I = Input

–

O = Output

–

I/O = Input/Output

–

D = Open drain

–

DS = Differential

–

A = Analog

Note: In the safe_mode, the buffer is configured in high-impedance.

6. BALL RESET STATE: The state of the terminal at reset (power up).

–

0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor.

–

1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor.

–

Z: High-impedance

–

L: High-impedance with an active pulldown resistor

–

H : High-impedance with an active pullup resistor

7. BALL RESET REL. STATE: The state of the terminal at reset release.

–

0: The buffer drives VOL (pulldown/pullup resistor not activated)

0(PD): The buffer drives VOL with an active pulldown resistor.

–

1: The buffer drives VOH (pulldown/pullup resistor not activated)

1(PU): The buffer drives VOH with an active pullup resistor.

–

Z: High-impedance

–

L: High-impedance with an active pulldown resistor

–

H : High-impedance with an active pullup resistor

8. RESET REL. MODE: This mode is automatically configured on release of the internal

GLOBAL_PWRON reset.

9. POWER: The voltage supply that powers the terminal’s I/O buffers.

10. HYS: Indicates if the input buffer is with hysteresis.

11. BUFFER STRENGTH: Drive strength of the associated output buffer.

12. PULL U/D - TYPE: Denotes the presence of an internal pullup or pulldown resistor. Pullup and

pulldown resistors can be enabled or disabled via software.

TERMINAL DESCRIPTION

Submit Documentation Feedback

OMAP3530-HiRel датащи(PDF) 12 Page - Texas Instruments

OMAP3530-HiRel датащи(HTML) 12 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL