| поискавой системы для электроныых деталей |
|
M16C/29 датащи(PDF) 244 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M16C/29 датащи(HTML) 244 Page - Renesas Technology Corp |
|
244 / 499 page ![]() 14. Serial I/O p u o r G 9 2 / C 6 1 M page 220 8 5 4 f o 7 0 0 2 , 0 3 .r a M 2 1 . 1 . v e R 2 1 1 0 - 1 0 1 0 B 9 0 J E R 14.2.1 SI/Oi Operation Timing Figure 14.37 shows the SI/Oi operation timing Figure 14.37 SI/Oi Operation Timing 14.2.2 CLK Polarity Selection The the SMi4 bit in the SiC register allows selection of the polarity of the transfer clock. Figure 14.38 shows the polarity of the transfer clock. Figure 14.38 Polarity of Transfer Clock D7 D0 D1 D2 D3 D4 D5 D6 i= 3, 4 1.5 cycle (max) SI/Oi internal clock CLKi output Signal written to the SiTRR register SOUTi output SINi input SiIC register IR bit (2) "H" "L" "H" "L" "H" "L" "H" "L" "H" "L" 1 0 (3) NOTES: 1. This diagram applies to the case where the SiC register bits are set as follows: SMi2 = 0 (SOUTi output), SMi3 = 1 (SOUTi output, CLKi function), SMi4 = 0 (transmit data output at the falling edge and receive data input at the rising edge of the transfer clock), SMi5 = 0 (LSB first) and SMi6 = 1 (internal clock) 2. When the SMi6 bit is set to 0 (internal clock), the SOUTi pin is placed in the high-impedance state after the transfer is completed. 3. If the SMi6 bit is set to 0 (internal clock), the serial I/O starts sending or receiving data a maximum of 1.5 transfer clock cycles after writing to the SiTRR register. (2) When the SMi4 bit in the SiC register is set to 1 (3) D1 D2 D3 D4 D5 D6 D7 D1 D2 D3 D4 D5 D6 D7 D0 D0 SINi SOUTi CLKi (1) When the SMi4 bit in the SiC register is set to 0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 SINi SOUTi CLKi (2) i=3 and 4 NOTES: 1. This diagram applies to the case where the SiC register bits are set as follows: SMi5 = 0 (LSB first) and SMi6 = 1 (internal clock) 2. When the SMi6 bit is set to 1 (internal clock), a high level is output from the CLKi pin if not transferring data. 3 When the SMi6 bit is set to 1 (internal clock), a low level is output from the CLKi pin if not transferring data. |
|
ссылки URL |
| Вашему бизинису помогли Аллдатащит? [ DONATE ] |
Что такое Аллдатащит | реклама | контакт | Конфиденциальность | Ссылка на техническое описание | обмен ссыками | поиск по производителю All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |