M16CSLASH29 datasheet(65/499 Pages) RENESAS

65 / 499 page

5. Resets

page 41

5.5.1 Low Voltage Detection Interrupt

If the D40 bit in the D4INT register is set to 1 (low voltge detection interrupt enabled), a low voltage

detection interrupt request is generated when voltage applied to the VCC pin is above or below Vdet4.

The low voltage detection interrupt shares the same interrupt vector with watchdog timer interrupt and

oscillation stop, re-oscillation detection interrupt.

Set the D41 bit in the D4INT register to 1 (enabled) to use the low voltage detection interrupt to exit stop

mode, set the D41 bit in the D4INT register to 1 (enable).

The D42 bit in the D4INT register is set to 1 (above or below Vdet4 detected) as soon as voltage applied

to the VCC pin goes above or below Vdet4 due to the voltage change. When the D42 bit setting changes

0 to 1, a low voltage detection interrupt is generated. Set the D42 bit to 0 (not detected) by program.

However, when the D41 bit is set to 1 and the MCU is in stop mode, a low voltage detection interrupt

request is generated, regardless of the D42 bit setting, if voltage applies to the VCC pin is detected to rise

above or drop below Vdet4. The MCU then exits stop mode.

Table 5.2

shows how a low voltage detection interrupt request is generated.

Bits DF1 and DF0 in the D4INT register determine sampling period that detects voltage applied to the

VCC pin rises above or drops below Vdet4. Table 5.3 shows sampling periods.

Table 5.2 Voltage Detection Interrupt Request Generation Conditions

Table 5.3 Sampling Clock Periods

D41 bit

VC27 bit

Operation Mode

D40 bit

D42 bit

CM02 bit

VC13 bit

Normal

operation

mode(1)

Wait mode

(2)

Stop mode

(2)

NOTES:

1. The status except the wait mode and stop mode is handled as the normal mode. (Refer to 7. Clock generating circuit)

2. Refer to 5.5.2 Limitations on stop mode and 5.5.3 Limitations on wait mode.

3. An interrupt request for voltage reduction is generated a sampling time after the value of the VC13 bit has changed.

Refer to the Figure 5.9 for details.

0 to 1

1 to 0

0 to 1

1 to 0

0 to 1

(3)

– : 0 or 1

(3)

CPU

clock

(MHz)

DF1 to DF0=00

(CPU clock divided by 8)

Sampling clock (µs)

3.0

6.0

12.0

24.0

DF1 to DF0=01

(CPU clock divided by 16)

DF1 to DF0=10

(CPU clock divided by 32)

DF1 to DF0=11

(CPU clock divided by 64)

M16C/29 датащи(PDF) 65 Page - Renesas Technology Corp

M16C/29 датащи(HTML) 65 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL