4513 datasheet(26/97 Pages) RENESAS

26 / 97 page

4513/4514 Group

SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER

MITSUBISHI MICROCOMPUTERS

(1) External 0 interrupt request flag (EXF0)

External 0 interrupt request flag (EXF0) is set to “1” when a valid

waveform is input to P30/INT0 pin.

The valid waveforms causing the interrupt must be retained at their

level for 4 clock cycles or more of the system clock (Refer to Figure

16).

The state of EXF0 flag can be examined with the skip instruction

(SNZ0). Use the interrupt control register V1 to select the interrupt

or the skip instruction. The EXF0 flag is cleared to “0” when an in-

terrupt occurs or when the next instruction is skipped with the skip

instruction.

The P30/INT0 pin need not be selected the external interrupt input

INT0 function or the normal I/O port P30 function. However, the

EXF0 flag is set to “1” when a valid waveform is input even if it is

used as an I/O port P30.

• External 0 interrupt activated condition

External 0 interrupt activated condition is satisfied when a valid

waveform is input to P30/INT0 pin.

The valid waveform can be selected from rising waveform, falling

waveform or both rising and falling waveforms. An example of

how to use the external 0 interrupt is as follows.

➀ Select the valid waveform with the bits 1 and 2 of register I1.

➁ Clear the EXF0 flag to “0” with the SNZ0 instruction.

➂ Set the NOP instruction for the case when a skip is performed

with the SNZ0 instruction.

➃ Set both the external 0 interrupt enable bit (V10) and the INTE

flag to “1.”

The external 0 interrupt is now enabled. Now when a valid wave-

form is input to the P30/INT0 pin, the EXF0 flag is set to “1” and the

external 0 interrupt occurs.

(2) External 1 interrupt request flag (EXF1)

External 1 interrupt request flag (EXF1) is set to “1” when a valid

waveform is input to P31/INT1 pin.

The valid waveforms causing the interrupt must be retained at their

level for 4 clock cycles or more of the system clock (Refer to Figure

16).

The state of EXF1 flag can be examined with the skip instruction

(SNZ1). Use the interrupt control register V1 to select the interrupt

or the skip instruction. The EXF1 flag is cleared to “0” when an in-

terrupt occurs or when the next instruction is skipped with the skip

instruction.

The P31/INT1 pin need not be selected the external interrupt input

INT1 function or the normal I/O port P31 function. However, the

EXF1 flag is set to “1” when a valid waveform is input even if it is

used as an I/O port P31.

• External 1 interrupt activated condition

External 1 interrupt activated condition is satisfied when a valid

waveform is input to P31/INT1 pin.

The valid waveform can be selected from rising waveform, falling

waveform or both rising and falling waveforms. An example of

how to use the external 1 interrupt is as follows.

➀ Select the valid waveform with the bits 1 and 2 of register I2.

➁ Clear the EXF1 flag to “0” with the SNZ1 instruction.

➂ Set the NOP instruction for the case when a skip is performed

with the SNZ1 instruction.

➃ Set both the external 1 interrupt enable bit (V11) and the INTE

flag to “1.”

The external 1 interrupt is now enabled. Now when a valid wave-

form is input to the P31/INT1 pin, the EXF1 flag is set to “1” and the

external 1 interrupt occurs.

4513 датащи(PDF) 26 Page - Renesas Technology Corp

4513 датащи(HTML) 26 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

датащи скачать

ссылки URL