LP5569ARTWR datasheet(27/93 Pages) TI2

27 / 93 page

LP5569

www.ti.com

SNVSAP8A – JULY 2017 – REVISED SEPTEMBER 2017

Product Folder Links: LP5569

Submit Documentation Feedback

(1)

These instructions are compatible with the LP5523 and LP55231 mux_* LED mapping instructions.

(2)

x - The instruction activates LED mapping to the driver when the instruction is executed.

Table 5. LED Mapping Instructions

INSTRUCTION(1)

ACT(2)

USAGE

COMPILER EXAMPLE

load_start

Define the LED mapping-table start address in SRAM.

load_start 01h; starting address

at 01h

map_start

Define the LED mapping-table start address in SRAM and set that

address active.

map_start 01h; starting address

at 01h

load_end

Define the last address of the LED mapping table in SRAM.

load_end 03h; last address at

03h

map_sel

Connect one LED driver to the LED engine.

map_sel 0; select LED0 as

output

map_clr

Clear the LED driver mappings in an engine

map_clr

map_next

Select the next address in the LED mapping table and set that address

active.

map_next

map_prev

Select the previous address in the LED mapping table and set that

address active.

map_prev

load_next

Move the mapping-table pointer to the next address.

load_next

load_prev

Move the mapping-table pointer to the previous address.

load_prev

load_addr

Set the mapping-table pointer to the assigned address.

load_addr 02h; set pointer to

02h

map_addr

Set the mapping-table pointer to the assigned address and set that

address active.

map_addr 02h; set mapping to

02h

(1)

This opcode is used with numerical operands.

(2)

This opcode is used with variables.

(3)

This is a new instruction, not available in LP5523 or LP55231

Table 6. Branch Instructions

INSTRUCTION

USAGE

COMPILER EXAMPLE

rst

Reset program counter to zero.

Reset

branch(1)

Branch to address. The number of loops can be set to a value or

do an infinite loop.

branch 20, loop1; do 20 loops to loop1 label

branch(2)

Branch to address. The loop count can be one of four variables A,

B, C, or D.

ld ra, 20 branch ra, loop1; do 20 loops to

loop1 label

int

Send an interrupt to the host system by pulling the GPIO/TRIG/INT

pin low.

int

end

End program execution and reset the program counter to zero.

Can also the set GPIO/TRIG/INT pin high and/or reset mapped

LED PWM and engine LED mapping.

end; end and reset LEDs.

trigger

Wait or send trigger. The trigger can be sent or received from an

external pin or another engine.

trigger w{e}; wait for external trigger

trig_clear(3)

Clear pending triggers.

trig_clear

jne

Jump if not equal. A != B

Jump to loop1 if A != B: jne ra, rb, loop1

Jump if less. A < B

Jump to loop1 if A < B : jl ra, rb, loop1

jge

Jump if greater or equal. A

≥ B

Jump to loop1 if A >= B: jge ra, rb, loop1

Jump if equal. A = B

Jump to loop1 if A = B: je ra, rb, loop1

LP5569ARTWR датащи(PDF) 27 Page - Texas Instruments

LP5569ARTWR датащи(HTML) 27 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93

датащи скачать

ссылки URL