PIC18F4685-ISLASHSP datasheet(37/484 Pages) MICROCHIP

37 / 484 page

Preliminary

DS39761B-page 35

PIC18F2682/2685/4682/4685

FIGURE 3-1:

TRANSITION TIMING FOR ENTRY TO SEC_RUN MODE

FIGURE 3-2:

TRANSITION TIMING FROM SEC_RUN MODE TO PRI_RUN MODE (HSPLL)

3.2.3

RC_RUN MODE

In RC_RUN mode, the CPU and peripherals are

clocked from the internal oscillator block using the

INTOSC multiplexer; the primary clock is shut down.

When using the INTRC source, this mode provides the

best power conservation of all the Run modes, while

still executing code. It works well for user applications

which are not highly timing sensitive or do not require

high-speed clocks at all times.

If the primary clock source is the internal oscillator

block (either INTRC or INTOSC), there are no distin-

guishable

differences

between

PRI_RUN

and

RC_RUN modes during execution. However, a clock

switch delay will occur during entry to and exit from

RC_RUN mode. Therefore, if the primary clock source

is the internal oscillator block, the use of RC_RUN

mode is not recommended.

This mode is entered by setting SCS1 to ‘1’. Although

it is ignored, it is recommended that SCS0 also be

cleared; this is to maintain software compatibility with

future devices. When the clock source is switched to

the INTOSC multiplexer (see Figure 3-3), the primary

oscillator is shut down and the OSTS bit is cleared. The

IRCF bits may be modified at any time to immediately

change the clock speed.

If the IRCF bits and the INTSRC bit are all clear, the

INTOSC output is not enabled and the IOFS bit will

remain clear; there will be no indication of the current

clock source. The INTRC source is providing the

device clocks.

If the IRCF bits are changed from all clear (thus,

enabling the INTOSC output) or if INTSRC is set, the

IOFS bit becomes set after the INTOSC output

becomes stable. Clocks to the device continue while

the INTOSC source stabilizes after an interval of

TIOBST.

OSC1

Peripheral

Program

T1OSI

Counter

Clock

CPU

Clock

PC + 2

123

n-1

Clock Transition

PC + 4

Q3 Q4

OSC1

Peripheral

Program

T1OSI

PLL Clock

PC + 4

Output

CPU Clock

PC + 2

Clock

Counter

Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.

SCS1:SCS0 bits Changed

TPLL(1)

n-1

Clock

OSTS bit Set

Transition

TOST(1)

Note:

Caution should be used when modifying a

single IRCF bit. If VDD is less than 3V, it is

possible to select a higher clock speed

than is supported by the low VDD.

Improper device operation may result if

the VDD/FOSC specifications are violated.

PIC18F4685-I/SP датащи(PDF) 37 Page - Microchip Technology

PIC18F4685-I/SP датащи(HTML) 37 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

датащи скачать

ссылки URL